Fdryvplsendpoint2table, Fdryvplsendpoint2vlanid, Fdryvplsendpoint2innertagtype – Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) User Manual
Page 631: Fdryvplsendpoint2innertag, Fdryvplsendpoint2ifindex, Fdryvplsendpoint2vlantagmode, Fdryvplsendpoint2inhcoctets, Fdryvplsendpoint2layer2state, Fdryvplsendpoint2operstatus, Fdryvplsendpoint2rowstatus
Unified IP MIB Reference
603
53-1002549-02
VPLS instance table
VPLS instance table
The following table can be used to configure additional virtual circuit properties that are not
supported in vplsConfigTable.
Name, OID, and syntax
Access
Description
fdryVplsEndPoint2Table
brcdIp.1.2.15.2.2.3
None
This table specifies information about the VPLS endpoints that
are not available in the PW MIB or the VPLS draft MIB. This
table replaces fdryVplsEndPointTable, as inner VLAN or ISID
has been added as an index of this table.
fdryVplsEndPoint2VlanId
brcdIp.1.2.15.2.2.3.1.1
Syntax: PwVlanCfg
None
This value specifies the VLAN ID value of this endpoint.
fdryVplsEndPoint2InnerTagType
brcdIp.1.2.15.2.2.3.1.2
Syntax: Integer
None
This value indicates the inner ID for the endpoint:
•
invalid(1)
•
innerVlan(2)
•
isid(3)
If no inner tag is specified, the value invalid(1) is returned.
fdryVplsEndPoint2InnerTag
brcdIp.1.2.15.2.2.3.1.3
Syntax: Unsigned32
None
This value indicates the inner ID for this endpoint. If the index
fdryVplsEndPoint2InnerTagType has the value isid(3), then this
object will have the ISID value for that endpoint. The valid ISID
value is between 256 (0x100) and 16777214 (0xFFFFFE). If
no inner tag is specified, the value 0 is returned.
fdryVplsEndPoint2IfIndex
brcdIp.1.2.15.2.2.3.1.4
Syntax: InterfaceIndex
None
This value specifies the ifIndex value of this endpoint.
fdryVplsEndPoint2VlanTagMode
brcdIp.1.2.15.2.2.3.1.5
Syntax: VlanTagMode
Read-create This value indicates the VLAN mode for this endpoint. The
values dual(3) and other(4) are not used in this table.
fdryVplsEndPoint2InHCOctets
brcdIp.1.2.15.2.2.3.1.6
Syntax: Counter64
Read-only
This counter indicates the number of octets ingressing into this
endpoint from the Customer Edge device. This object is
supported only on the Brocade NetIron CES and Brocade
NetIron CER series devices.
fdryVplsEndPoint2Layer2State
brcdIp.1.2.15.2.2.3.1.7
Syntax: Layer2StateTC
Read-only
The Layer 2 state of this VPLS endpoint.
fdryVplsEndPoint2OperStatus
brcdIp.1.2.15.2.2.3.1.8
Syntax: PwOperStatusTC
Read-only
This object indicates the operational status of this endpoint:
•
up(1)
•
down(2)
No other values are used in this table.
fdryVplsEndPoint2RowStatus
brcdIp.1.2.15.2.2.3.1.9
Syntax: RowStatus
Read-create This variable is used to create, modify, and delete a row in this
table. When a row in this table is in active(1) state, no objects
in that row can be modified except this object and the
fdryVplsEndPointAdminStatus object.