Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 181)

Unified IP MIB Reference 153
53-1002549-02
Agent board table
snAgentBrdMediaLedString
brcdIp.1.1.2.2.1.1.19
Syntax: OCTET STRING
NOTE: This object is not
supported on the
Brocade MLXe, Brocade
NetIron MLX, Brocade
NetIron XMR, Brocade
NetIron CES, and
Brocade NetIron CER
series devices.
Read-only Applies to devices with an LED for media type. It contains an octet
string with 64-bits per slot. The value of each bit can be one of the
following:
•
0 – Half-duplex
•
1 – Full-duplex
snAgentBrdSpeedLedString
brcdIp.1.1.2.2.1.1.20
Syntax: OCTET STRING Read-only Applies to devices that have an LED for traffic speed. Contains an
octet string with 64-bits per slot. The value of each bit can be one
of the following:
•
0 – 10 Mbit
•
1 – 100 Mbit
snAgentBrdAlarmLedString
brcdIp.1.1.2.2.1.1.21
Syntax: OCTET STRING Read-only Applies to devices that have an alarm LED. Contains an octet string
with 64-bits per slot. The value of each bit can be one of the
following:
•
0 – No alarm
•
1 – Alarm
snAgentBrdTxTrafficLedString
brcdIp.1.1.2.2.1.1.22
Syntax: OCTET STRING Read-only Applies only to POS modules. Contains an octet string with 64-bits
per slot. The value of each bit can be one of the following:
•
0 – No transmit traffic
•
1 – Transmit traffic
snAgentBrdRxTrafficLedString
brcdIp.1.1.2.2.1.1.23
Syntax: OCTET STRING Read-only Applies only to POS modules. Contains an octet string with 64-bits
per slot. The value of each bit can be one of the following:
•
0 – No receive traffic
•
1 – Receive traffic
snAgentBrdMemoryTotal
brcdIp.1.1.2.2.1.1.24
Syntax: CounterBasedGauge64 Read-only Shows the total memory in bytes within this module.
snAgentBrdMemoryAvailable
brcdIp.1.1.2.2.1.1.25
Syntax: CounterBasedGauge64 Read-only Shows the available total memory in bytes within this module.
snAgentBrdSerialNumber
brcdIp.1.1.2.2.1.1.26
Syntax: DisplayString Read-only Indicates the serial number of the board only for Brocade NetIron
XMR, Brocade NetIron MLX, and Brocade MLXe router devices. No
string is displayed if the serial number has not been programmed in
the EEPROM or the module does not support a serial number.
snAgentBrdPartNumber
brcdIp.1.1.2.2.1.1.27
Syntax: DisplayString Read-only Indicates the part number of the board only for Brocade NetIron
XMR , Brocade NetIron MLX, and Brocade MLXe router devices.
Nothing is displayed if the part number has not been programmed
in the EEPROM or the module does not support a part number.
snAgentBrdMemoryUtil100thPe
rcent
brcdIp.1.1.2.2.1.1.28
Syntax: Unsigned32 Read-only Indicates the dynamic memory that is currently utilized within this
module, in units of one-hundredth of a percent.
Name, OID, and syntax Access Description