Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 220)

192 Unified IP MIB Reference
53-1002549-02
Switch port information
snSwIfInfoTagType
brcdIp.1.1.3.3.5.1.5
Syntax: Integer32 Read-write Indicates the IEEE802.1q tag type of an interface. The tag type is
embedded in the two octets in the length or type field of an Ethernet
packet. It specifies that the two octets after the length or type field in an
Ethernet packet is the tag value.
Default value: 33024
snSwIfInfoChnMode
brcdIp.1.1.3.3.5.1.6
Syntax: Integer Read-write Indicates if the port operates in half- or full-duplex mode:
•
none(0) – This is not used.
•
halfDuplex(1) – Half-duplex mode. Available only for 10/100 Mbps
ports.
•
fullDuplex(2) – Full-duplex mode. 100BaseFx, 1000BaseSx, and
1000BaseLx ports operate only at fullDuplex(2).
The read-back channel status from hardware are as follows:
•
halfDuplex(1) – Half-duplex mode.
•
fullDuplex(2) – Full-duplex mode.
The port media type (expansion or regular) and port link type (trunk or
feeder) determine the value of this object. The port cannot be set to
half-duplex mode if the port connect mode is m200e(4). However, the
value of this parameter may be automatically set whenever the
expansion port is connected, for example, in the case of a
cascade-connecting device.
snSwIfInfoSpeed
brcdIp.1.1.3.3.5.1.7
Syntax: Integer Read-write Indicates the speed configuration for a port:
•
none(0) – Link down or no traffic.
•
sAutoSense(1) – Auto-sensing 10 or 100 Mbits.
•
s10M(2) – 10 Mbits per second.
•
s100M(3) – 100 Mbits per second.
•
s1G(4) – 1 Gbits per second.
•
s1GM(5) – 1 Gbits per second master.
•
s155M(6) – 155 Mbits per second (ATM) (for expansion board only).
•
s10G(7) – 10 Gbits per second.
•
s622M(8) – OC12 - 622 Mbits per second. (Brocade NetIron XMR,
Brocade NetIron MLX, and Brocade MLXe router.)
•
s2488M(9) – OC48 - 2.488 Gbits per second. (Brocade NetIron
XMR, Brocade NetIron MLX, and Brocade MLXe router.)
•
s9953M(10) – OC192 - 9.953 Gbits per second. (Brocade NetIron
XMR router, Brocade MLX router, and Brocade MLXe router.)
•
s16G(11) - 16 Gbits per second.
•
s100G(12) - 100 Gbits per second.
•
s40G(13) - 40 Gbits per second.
The read-back hardware status are the following:
•
none(0) – Link down or no traffic.
•
s10M(2) – 10 Mbits per second.
•
s100M(3) – 100 Mbits per second.
•
s1G(4) – 1G bits per second.
•
s1GM(5) - 1G bits per second master.
•
s155M(6) – 155 Mbits per second (ATM) (for expansion board only).
•
s10G(7) – 10 Gbits per second.
Name, OID, and syntax Access Description