Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 534)

506 Unified IP MIB Reference
53-1002549-02
OSPF general objects
snOspfASBdrRtrStatus
brcdIp.1.2.4.1.3
Syntax: TruthVal Read-write Indicates if this router is an Autonomous System Boundary Router:
•
false(0)
•
true(1)
snOspfRedisMode
brcdIp.1.2.4.1.4
Syntax: Integer Read-write Specifies if OSPF redistribution has been enabled on this router:
•
disabled(0) – OSPF redistribution is disabled.
•
enabled(1) – OSPF redistribution is active.
snOspfDefaultOspfMetric
Value
brcdIp.1.2.4.1.5
Syntax: Integer Read-write Shows the cost of using a default OSPF metric value on this route.
Valid values: 1 – 65535
snOspfExternLSACount
brcdIp.1.2.4.1.6
Syntax: Gauge32 Read-only The number of external link-state advertisements in the link-state
database.
snOspfExternLSACksumS
um
brcdIp.1.2.4.1.7
Syntax: Integer32 Read-only Indicates the 32-bit unsigned sum of the link-state (LS) checksums of
the external link-state advertisements (LSA) contained in the link-state
database. This sum can be used to determine if there has been a
change in a router’s link-state database and to compare the link-state
database of two routers.
snOspfOriginateNewLSAs
brcdIp.1.2.4.1.8
Syntax: Counter Read-only Shows the number of new link-state advertisements that have been
originated by the router. This number increments each time the router
originates a new LSA.
snOspfRxNewLSAs
brcdIp.1.2.4.1.9
Syntax: Counter32 Read-only Shows the number of link-state advertisements received by the router.
This number does not include newer instantiations of self-originated
link-state advertisements.
snOspfOspfRedisMetricTy
pe
brcdIp.1.2.4.1.10
Syntax: Integer Read-write Indicates the type of route:
•
type1(1) – External Type 1 (comparable value) intra-area and
inter-area routes. It is an OSPF metric plus the external metric.
•
type2(2) – External Type 2 (non-comparable value) routes. It is the
external metric.
snOspfExtLsdbLimit
brcdIp.1.2.4.1.11
Syntax: Integer32 Read-write Provides compliance with RFC 1765 in the handling of OSPF external
link-state database (LSDB) overflow.
Specifies the maximum number of non-default AS-external-LSAs
entries that can be stored in the link-state database. When the number
of non-default AS-external-LSAs in a router’s link-state database
reaches ospfExtLsdbLimit, the router enters overflow state.The router
never holds more than ospfExtLsdbLimit non-default AS-external-LSAs
in its database. OspfExtLsdbLimit must be set identically in all routers
attached to the OSPF backbone and any regular OSPF area. OSPF stub
areas and NSSAs are excluded.
Valid values: 1 – 2000.
NOTE: There is not limit, if the value is -1.
snOspfExitOverflowInterv
al
brcdIp.1.2.4.1.12
Syntax: Integer Read-write Specifies the number of seconds that a router will attempt to leave the
overflow state. This value allows the router to again originate
non-default AS-external-LSAs. If this object is set to 0, the router will
not leave the overflow state until it is restarted.
Valid values: 0 – 86400 seconds
Name, OID, and syntax Access Description