Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 450)

422 Unified IP MIB Reference
53-1002549-02
MCT cluster table
Name, OID, and syntax Access Description
brcdMctClusterTable
brcdIp.1.1.12.1.1.2 None The MCT cluster table.
brcdMctClusterId
brcdIp.1.1.12.1.1.2.1.1
Syntax: Unsigned32 None The ID of the MCT cluster.
brcdMctClusterName
brcdIp.1.1.12.1.1.2.1.2
Syntax: DisplayString Read-create The name of the MCT cluster. The object cannot be modified after
creation.
Valid values: 1 – 64
brcdMctClusterRbridgeId
brcdIp.1.1.12.1.1.2.1.3
Syntax: Unsigned32 Read-create The remote bridge ID of the MCT cluster. The remote bridge ID is
used by the peer to communicate with the cluster node.
Valid values: 1 – 35535
brcdMctClusterSessionVlan
brcdIp.1.1.12.1.1.2.1.4
Syntax: BrcdVlanIdTC Read-create The session VLAN of the MCT cluster. The cluster session VLAN
ranges from 1 through 4090, but it cannot be a default VLAN.
The brcdMctClusterSessionVlan and brcdMctClusterKeepAliveVlan
objects cannot be the same value.
brcdMctClusterKeepAliveVla
n
brcdIp.1.1.12.1.1.2.1.5
Syntax:
BrcdVlanIdOrNoneTC Read-create The keepalive VLAN of the MCT cluster. The keepalive VLAN ranges
from 0 through 4090, but it cannot be a default VLAN.
The brcdMctClusterSessionVlan and brcdMctClusterKeepAliveVlan
objects cannot be the same value.
The value 0 indicates the keepalive VLAN is not set for the
particular cluster.
If the brcdMctClusterClientIsolationMode object is set to strict(2),
then the brcdMctClusterKeepAliveVlan object cannot be set to any
value other than 0.
Default: 0
brcdMctClusterClientIsolatio
nMode
brcdIp.1.1.12.1.1.2.1.6
Syntax: Integer Read-create The client isolation mode of the MCT cluster.
•
loose(1)—Indicates the Cluster Communication Protocol (CCP)
is down and the client performs the master/slave negotiation.
After negotiation, the slave shuts down the client ports,
whereas the master client ports continue to forward the traffic.
•
strict(2)—Indicates the CCP goes down and the client interface
on both the cluster nodes is administratively shut down. In this
mode, the client is isolated from the network if CCP is not
operational.
If the brcdMctClusterKeepAliveVlan object is set to any value other
than 0, then the brcdMctClusterClientIsolationMode object cannot
be set to strict(2).
Default: loose(1)
brcdMctClusterClientShutdo
wn
brcdIp.1.1.12.1.1.2.1.7
Syntax: TruthVal Read-create The client shutdown state of the MCT cluster.
Shuts down the entire local client interface in the cluster when the
value is set to true. This results in the failover of the traffic to the
cluster peer.
Default: false
brcdMctClusterMemberVlan
s
brcdIp.1.1.12.1.1.2.1.8
Syntax: DisplayString Read-create The list of the member VLAN IDs on which the MCT cluster is
operating. This is the range of VLANs that has MAC synchronization.
•
The VLANs that are not sequential are represented as
separated by a space; for example, 2 5 100.
•
The VLANs that are continuous and sequential are
represented as a range; for example, 10 to 40.