Interlogix VEREX Director - Manual (Page 261)

21-0381E v4.9.1 Welcome Report Control Admin Sys Config Tech-Ref 253
"arming station".
An arming station includes a Wiegand reader with
keypad, and supports additional functions for arming
and disarming areas, adjusting the area closing time
(worklate), etc. For details, refer to the User's Guide
for your xL system (panel/LCD keypad).
Note: Arming-station wiring differs from other readers
(ensure the proper installation instructions have been
followed).
- Enable Class Checking:
Selected (): This selection is required if user-
access to this reader is to be controlled based on time
of day and/or door class. See [Class Map] to
follow/below. Not Selected: Provides 24-hr
access/egress to all valid cards regardless of the
users' assigned schedule and door class authorities.
[Class Map]
- Schedule, In / Out of schedule, and Class
A/B/C: These settings allow restricting
access to only the users with specific door-
class authority, and/or optionally blocking
after-hours access to this specific reader
(except users with 'Master Override'
authority). If scheduled, a different set of
door-class requirements can be selected for
when the schedule is active versus outside of
the chosen schedule.
To block after-hours access to this reader, select "Out
of Schedule" None. To remove class restrictions at
this reader (without bypassing each user's assigned
schedule), select A, B, C for both "In Schedule"
and "Out of Schedule".
Related Settings:
 User's door-class authorities and scheduling are set
under: Authorities, Profile 1-4,  Door
Class. See: Authorities for Users / Entrants.
- Group Number: Similar to 'Door Class'.
Each reader can be assigned a value here.
Users can enter only if their assigned
authority supports this group number.
-------------------------
- Log APB Violation Only: This will cause
APB violations to be recorded, while allowing
the person to enter.
- Detect Antipassback: This enables /
disables the Antipassback feature for this
reader.
Antipassback (APB): A feature that blocks individual
cards from being used to:
+ Re-enter the same area, or;
+ Re-enter the facility from 'outside', and/or;
+ (Optional): Enter other areas;
…Unless they are recorded as exiting first--i.e., each
person must use their card/token at every reader they
encounter (that is set to "Detect Antipassback"). Tip:
This helps to protect against unauthorized card usage.
Note: Antipassback-controlled areas typically require
an exit reader on each door.
Antipassback operation can be customized on an
area-by-area basis. For details, refer to
"Antipassback" under "Areas and Related Settings".
The antipassback status can be reset for a specific
user, or for all users in a specific area (to allow their
next entry or exit regardless of their previous APB
status). For details, refer to "Resetting Users'
Antipassback Status", and/or "Resetting the
Antipassback Status for Users in a Specific Area" in
the Control & Status Chapter.
[Card Action]
- Card Action: This is an optional feature that
sets a reader to enable (enrol) or disable
(invalidate) a selected type of cards when
accepted by the reader. You can select whether
or not the door will also unlock, and other
parameters (to follow.)
Blue Text: With a card-enrolment reader (i.e., "Enable
Cards"), you can set whether expired and/or
"Enrolment Pending" cards will be affected (Also see:
'Related Settings', after "Option"--to follow / below).
The present selection for this will be shown in blue
text. Application Tip: 'Expired' cards also includes
cards that had been previously enabled for a set
period of time.
Access vs. Card Action vs. Denied: Valid cards that
are not affected by the 'Card Action' will simply be
granted access (i.e., the reader will operate like any
other reader). This includes cards that are already
valid (enrolment reader), and cards other than the
selected 'Card Type'. Cards that are NOT authorized
for this reader at this time (per user authorities), will be
denied access, and the card-action will NOT occur.
- Card Type: The type of cards to be affected by
an 'enable' or 'disable' card-action.
Never: Normal operation (same as selecting "No
Card Action");
Escort-Required Users: Users with "Visitor (Escort
Required)" authority (although an escort will not be
needed for cards being enabled/disabled);
Tip: To enforce the 'escort' requirement for visitors at
an enrolment station, ensure "Unlock Door..." is NOT
selected. The visitor can 'badge' once to enable the
card initially, and then the visitor and escort can use
their cards to gain entry as usual.
Temporary Users: All cards that are set with an
expiry date;
All Users: All cards presented at this reader (with
authority for its area).