Basler Electric DECS-250N - Manual (Page 263)

9440500990 Rev D 247
DECS-250N PROFIBUS Communication
Instance Name Inst. # Type RW Key Name Unit Range
Synchronizer Metering
Cyclic 5 Float R Slip Angle GG Deg -359.9 - 359.9
Synchronizer Metering
Cyclic 5 Float R Slip Freq GG Hz n/a
Synchronizer Metering
Cyclic 5 Float R Voltage Diff GG V n/a
Limiter Status Cyclic 6 UINT8 R ALARMS OEL ALM Not Active=0, Active=1
Limiter Status Cyclic 6 UINT8 R ALARMS UEL ALM Not Active=0, Active=1
Limiter Status Cyclic 6 UINT8 R ALARMS SCL ALM Not Active=0, Active=1
Limiter Status Cyclic 6 UINT8 R ALARMS VAR
LIMITER ACTIVE Not Active=0, Active=1
Limiter Status Cyclic 6 UINT8 R ALARMS
UNDERFREQUENCYVHZ
ALM Not Active=0, Active=1
HMI Indicators Cyclic 7 UINT8 R DECSCONTROL
DECS NULL BALANCE Not Active=0, Active=1
HMI Indicators Cyclic 7 UINT8 R DECSPSSMETER
DECS PSS ACTIVE Not Active=0, Active=1
HMI Indicators Cyclic 7 UINT8 R DECSREGULATORMETER
DECS
INTERNAL TRACKING
ACTIVE Not Active=0, Active=1
HMI Indicators Cyclic 7 UINT8 R DECSCONTROL DECS
PREPOSITION Active setpoint is not at a pre-
position value=0, Active setpoint is
at a pre-position value=1
HMI Indicators Cyclic 7 UINT8 R DECSREGULATORMETER
SETPOINT
AT LOWER LIMIT Active setpoint is not at minimum
value=0, Active setpoint is at
minimum value=1
HMI Indicators Cyclic 7 UINT8 R DECSREGULATORMETER
SETPOINT
AT UPPER LIMIT Active setpoint is not at maximum
value=0, Active setpoint is at
maximum value=1
Controller Status Cyclic 8 UINT8 R DECSCONTROL IN AVR
MODE Not in AVR mode=0, In AVR
mode=1
Controller Status Cyclic 8 UINT8 R DECSCONTROL IN FCR
MODE Not in FCR mode=0, In FCR
mode=1
Controller Status Cyclic 8 UINT8 R DECSCONTROL IN FVR
MODE Not in FVR mode=0, In FVR
mode=1
Controller Status Cyclic 8 UINT8 R DECSCONTROL IN PF
MODE Not in PF mode=0, In PF mode=1
Controller Status Cyclic 8 UINT8 R DECSCONTROL IN VAR
MODE Not in var mode=0, In var mode=1
System Status Cyclic 9 UINT8 R DECSCONTROL DECS
START STOP Stopped=0, Started=1
System Status Cyclic 9 UINT8 R ALARMS IFLIMIT No field short circuit condition=0,
Field short circuit condition=1
System Status Cyclic 9 UINT8 R DECSCONTROL DECS
SOFT START ACTIVE Not in soft start=0, In soft start=1
System Status Cyclic 9 UINT8 R ALARMREPORT
ALARMOUTPUT No active alarms=0, Active
alarms=1
System Status Cyclic 9 UINT8 R DECSCONTROL DECS PF
VAR
ENABLE 52 J K PF/var not enabled via PLC=0,
PF/var enabled via PLC=1
System Status Cyclic 9 UINT8 R DECSCONTROL DECS
PARALLEL
ENABLE 52 L M Parallel not enabled via PLC=0,
Parallel enabled via PLC=1
Local Contact Inputs Cyclic 10 UINT8 R CONTACTINPUTS
STARTINPUT Open=0, Closed=1
Local Contact Inputs Cyclic 10 UINT8 R CONTACTINPUTS
STOPINPUT Open=0, Closed=1
Local Contact Inputs Cyclic 10 UINT8 R CONTACTINPUTS INPUT1 Open=0, Closed=1
Local Contact Inputs Cyclic 10 UINT8 R CONTACTINPUTS INPUT2 Open=0, Closed=1
Local Contact Inputs Cyclic 10 UINT8 R CONTACTINPUTS INPUT3 Open=0, Closed=1