Lenze E94ARNE Regenerative power supply - Manual (Page 357)

EDS94ARNExxxx EN 2.3 - 06/2014
L
357
9400 regenerative power supply module | Parameter setting
Index
Program auto-start (C02104) 331
Program name (C02113) 332
Program runtime (C02109) 332
Program status (C02108) 331
Project not available (error message) 237
Project not loaded (error message) 237
Q
Quick stop by trouble 79
R
Rated power of brake resistor (C00130) 281
Read error service register (error message) 221
Real-time clock 328 , 329
Red. brake chopper threshold (C00181) 288
Reference
Brake chopper utilisation (C00133) 282
Required licence missing (error message) 237
Required safety module (C00214) 292
Resetting an error message 202
Resp to new firmw. standard dev. (C00635) 321
Resp. brake resist.
i2t > C00572 (C00571) 314
Resp. brake trans. ixt > C00570 (C00569) 313
Resp. to 10% overvoltage on Line (C00602) 318
Resp. to 10% undervoltage on Line (C00601) 318
Resp. to CAN bus OFF (C00595) 317
Resp. to CAN heartbeat error (C00613) 320
Resp. to CAN life guarding error (C00614) 320
Resp. to CAN node guarding error (C00612) 319
Resp. to CAN-RPDOx error (C00591) 317
Resp. to comm. error with MXI1 (C01501) 330
Resp. to comm. error with MXI2 (C01502) 330
Resp. to CPU temp. > C00126 (C00589) 316
Resp. to DC bus overvoltage (C00600) 318
Resp. to device overload > C00123 (C00604) 319
Resp. to external fault (C00581) 315
Resp. to failure heatsink fan (C00610) 319
Resp. to failure integral fan (C00611) 319
Resp. to failure t. sensor drive (C00588) 316
Resp. to failure t. sensor filter (C00594) 317
Resp. to filter KTY overtemp. (C00583) 315
Resp. to filter PTC overtemp. (C00585) 316
Resp. to filter temp. > C00121 (C00584) 315
Resp. to heatsink temp. > C00122 (C00582) 315
Resp. to imp. device config. (C00615) 320
Resp. to new module in MXI1 (C00636) 321
Resp. to new module in MXI2 (C00637) 321
Resp. to open circuit AIN1 (C00598) 318
Resp. to overload brake trans. (C00573) 314
Resp. to overtemp. brake resist. (C00574) 314
Resp. to task overflow (C02111) 332
Restart 84
Restore default parameters (I-1011) 152
RPDO1 communication parameter (I-1400) 161
RPDO1 mapping parameter (I-1600) 163
RPDO2 communication parameter (I-1401) 162
RPDO2 mapping parameter (I-1601) 164
RPDO3 communication parameter (I-1402) 162
RPDO3 mapping parameter (I-1602) 164
RPDO4 communication parameter (I-1403) 163
RPDO4 mapping parameter (I-1603) 164
Runtime ApplicationTask (C02121) 332
Runtime IdleTask (C02123) 333
Runtime measurement 53
Runtime UserTask (C02122) 332
S
Safety instructions 11
Safety module
Incompatible with setting in C00214 (error
message) 244
Safety module has been changed (error message) 214
Safety module has been removed (error message) 211
Safety module is defect or missing (error message)
210 , 212
Sampled peak power (C00143) 283
Saving of parameters failed (error message) 240
SDO1 server parameter (I-1200) 156
SDO10 server parameter (I-1209) 160
SDO2 server parameter (I-1201) 157
SDO3 server parameter (I-1202) 159
SDO4 server parameter (I-1203) 159
SDO5 server parameter (I-1204) 159
SDO6 server parameter (I-1205) 159
SDO7 server parameter (I-1206) 160
SDO8 server parameter (I-1207) 160
SDO9 server parameter (I-1208) 160
Selected control scheme (C00006) 275
Service code (C00159) 285
Service code (C00180) 288
Service code (C00469) 312
Service password (C00004) 275
Set time and date (C01215) 329
Setting the CAN baud rate 102
Setting the CAN node address 101
Setting the error response 197
Short overview of error messages 203
Signal configuration 30
Starting performance 84
State bus 96
Status
Digital inputs (C00443) 311
Digital outputs (C00444) 311
Status DCTRL control input (C00878) 324
Status displays 187