Lenze E94ARNE Regenerative power supply - Manual (Page 351)

EDS94ARNExxxx EN 2.3 - 06/2014
L
351
9400 regenerative power supply module | Parameter setting
Index
COB-ID 104
COB-ID EMCY (I-1014) 153
COB-ID SYNC message (I-1005) 149
Code Refresh (error message) 215
Combination memory module/device not possible
(error message) 214
Combination MXI1/MXI2 not possible (error message)
214
Combination of module in MXI1/device not possible
(error message) 215
Combination of module in MXI2/device not possible
(error message) 215
Communication cycle period (I-1006) 150
Communication error between device and device
module (error message) 231
Communication task
Standstill > 3 s (error message) 243
Communication with module in MXI1 interrupted
(error message) 231
Communication with module in MXI2 interrupted
(error message) 232
Communication with safety module interrupted (error
message) 244
Config. analog input 1 (C00034) 276
Consumer heartbeat time (I-1016) 154
Control card
Supply voltage (24 V DC) too low (error message)
220
Control card incompatible (error message) 212
Control card is defect (error message) 209 , 211
Control card is defect (UB18 neg.) (error message) 225
Control card is defect (UB24) (error message) 224
Control card is defect (UB8) (error message) 224
Control card is defect (VCC15 neg.) (error message)
224
Control card is defect (VCC15) (error message) 224
Control card is defect (VCC5) (error message) 225
Controller inhibit by (source) (C00158) 285
Counter
Brake chopper overload (C01203) 327
DC bus overvoltage (C01205) 327
Heatsink overtemp. (C01208) 328
Housing overtemp. (C01209) 328
Ixt overload (C01204) 327
Mains switching (C01206) 328
Power section overload (C01212) 328
CPU
Overtemperature (error message) 222
Temperature > C00126 (error message) 222
Thermal detector is defect (error message) 223
CPU temp. warning threshold (C00126) 281
CPU temperature (C00069) 278
Current contr. reset time (C00076) 279
Current controller gain (C00075) 278
Cyclic task
Standstill > 60 s (error message) 243
D
Data type 266
Date 328 , 329
DC bus overvoltage (error message) 226
DC bus undervoltage (error message) 226
DC bus voltage ctrl. gain (C00070) 278
DC bus voltage ctrl. reset time (C00071) 278
DC-bus capacitor
Thermal detector is defect (error message) 223
DC-bus voltage (C00053) 277
Device
Pulse inhibit is active (error message) 221
Device command status (C00003) 275
Device commands (C00002) 272
Device commands, commands
see device commands, C2 (device command), C3
(device command status) 37
Device enabled (error message) 221
Device interface 259
Device name (C00199) 289
Device state (C00183) 288
Device type (I-1000) 147
Device utilisation (Ixt) (C00064) 278
Device utilisation Ixt > 100 % (error message) 224
Device utilisation Ixt > C00123 (error message) 224
DI_bErrors (C02548) 333
DI_dnState (C02547) 333
Diagnostics X6
Change baud rate (C01903) 331
Curr. baud rate (C01905) 331
Max. baud rate (C01902) 331
Dig. input x
Terminal polarity (C00114) 280
Dig. output x
Terminal polarity (C00118) 280
Digital inputs 94
Delay time (C02830) 339
Digital outputs 95
Division by zero (error message) 219
Drive interface 36
Signals (C02549) 334
DRIVE-ERROR LED 188
DRIVE-READY LED 188
E
ECTRL_dnDCBusVoltage (C00779) 322
ECTRL_dnIfilterAct (C00780) 323
ECTRL_dnIxtLoad (C00786) 323
ECTRL_dnLineFreqAct (C00784) 323
ECTRL_dwLineVoltageAct (C00783) 323
ECTRL_dwMaxDeviceCurrent (C00789) 323
Elapsed hour meter (C00178) 287
Electronic nameplate
Data are incompatible (error message) 225