Brocade Network OS Administrator’s Guide v4.1.1 - Manual (Page 692)

Unicasts: 10641, Multicasts: 2637, Broadcasts: 1976
64-byte pkts: 10874, Over 64-byte pkts: 3294, Over 127-byte pkts: 117
Over 255-byte pkts: 969, Over 511-byte pkts: 0, Over 1023-byte pkts: 0
Over 1518-byte pkts(Jumbo): 0
Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0
Errors: 0, Discards: 0
Transmit Statistics:
12633 packets, 1155963 bytes
Unicasts: 18, Multicasts: 12615, Broadcasts: 0
Underruns: 0
Errors: 0, Discards: 0
Rate info (interval 299 seconds):
Input 0.000128 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 1d00h40m
3. Enter the show media interface command to check that the optics used are Brocade-certified.
Verify the Vendor Name field, shown underlined in the following example, reads BROCADE. If the
Vendor Name field shows anything other than BROCADE, replace the optics with Brocade-certified
optics.
Check also the TX Power and RX Power fields to ensure they are not zero.
switch# show media interface tengigabitethernet 66/0/60
Interface TenGigabitEthernet 66/0/60
Identifier 3 SFP
Connector 7 LC
Transceiver 0000000000000010 10_GB/s
Name id
Encoding 6
Baud Rate 103 (units 100 megabaud)
Length 9u 0 (units km)
Length 9u 0 (units 100 meters)
Length 50u 8 (units 10 meters)
Length 62.5u 3 (units 10 meters)
Length Cu 0 (units 1 meter)
Vendor Name BROCADE
Vendor OUI 00:05:1e
Vendor PN 57-0000075-01
Vendor Rev A
Wavelength 850 (units nm)
Options 001a
BR Max 0
BR Min 0
Serial No AAA209282044472
Date Code 090709
Temperature 35 Centigrade
Voltage 3356.4 (mVolts)
Current 5.564 (mAmps)
TX Power 568.9 (uWatts)
RX Power 549.9 (uWatts)
4. Enter the show mac-address-table command to verify that the MAC address table learns new
values.
The new MAC address should appear here.
switch# show mac-address-table
VlanId Mac-address Type State Ports
1002 0efc.0042.7300 FPMA Active Te 66/0/55
1002 0efc.0042.7302 FPMA Active Te 66/0/55
1002 0efc.0042.7800 FPMA Active Te 66/0/60
Total MAC addresses : 3
5. Enter the show lldp neighbors command to verify that LLDP reports all neighbors.
switch# show lldp neighbors
Local Intf Dead Interval Remaining Life Remote Intf Chassis ID Tx Rx
Te 66/0/55 120 101 port1 0005.1e78.f004 3000
2948
Te 66/0/60 120 117 port0 0005.1e55.16c8 2999
2945
If the output does not show all neighbors, contact your switch support provider.
6. Enter the show mac-address-table command to verify the Ethernet Name Service functionality
and to detect whether MAC addresses learned from other VCS Fabric switches are present.
Troubleshooting procedures
692 Network OS Administrator’s Guide
53-1003225-04