beautypg.com

Brocade Network OS Administrator’s Guide v4.1.1 User Manual

Page 558

background image

17 10:00:00:05:33:77:31:9C* 10.24.73.80 Online RB1

18 >10:00:00:05:33:77:23:6C 10.24.73.85 Online RB2

4. Verify the in-band management connection to RB1 and RB2.

a)

Connect to C1 from the management station using an SSH connection.

b)

On C1, verify connectivity to RB1 (local test) by issuing the ping command to the front-end
Ethernet interface (Ve port) IP address for RB1.

C1# ping 2.2.2.17

PING 2.2.2.17 (2.2.2.17): 56 data bytes

64 bytes from 2.2.2.17: icmp_seq=0 ttl=64 time=8.206 ms

64 bytes from 2.2.2.17: icmp_seq=1 ttl=64 time=7.126 ms

--- 2.2.2.17 ping statistics ---

c)

From C1, verify connectivity to RB2 (remote test) by issuing the ping command to the
front-end Ethernet interface (VE port) IP address for RB2.

C1# ping 100.100.100.18

PING 100.100.100.18 (100.100.100.18): 56 data bytes

64 bytes from 100.100.100.18: icmp_seq=0 ttl=63 time=21.239 ms

64 bytes from 100.100.100.18: icmp_seq=1 ttl=63 time=19.889 ms

--- 100.100.100.18 ping statistics ---

d)

From C1, establish a Telnet connection to RB1 by issuing the telnet command to the front-
end Ethernet interface (Ve port) IP address for RB1.

This test verifies the in-band management interface between C1 and the local RBridge,
RB1. If the test succeeds, you can perform management functions on RB1 through C1.

C1# telnet 2.2.2.17

Trying 2.2.2.17...

Connected to 2.2.2.17

Escape character is '^]'.

e)

Verify the Telnet RASLog notification on RB1 through C1.

The RASLog message displays on the console.

RB1# 2012/05/10-17:31:09, [SEC-1203], 312942, M1, INFO, C1, Login

information: Login successful via TELNET/SSH/RSH. IP Addr: 2.2.2.1

f)

Verify the VCS fabric configuration on RB1 through C1.

The output is identical to the output generated in step 3d. The difference is that you are
now connected to RB1 through the in-band management interface.

RB1# show vcs

Config Mode : Local-Only

VCS ID : 2

Total Number of Nodes : 2

Rbridge-Id WWN Management IP Status HostName

------------------------------------------------------------------

17 10:00:00:05:33:77:31:9C* 10.24.73.80 Online RB1

18 >10:00:00:05:33:77:23:6C 10.24.73.85 Online RB2

g)

From C1, establish a Telnet connection to RB2 by issuing the telnet command to the front-
end Ethernet interface (VE port) IP address for RB2.

This test verifies the in-band management interface between C1 and the remote RBridge,
RB2. If the test succeeds, you can perform management functions on RB2 through C1.

C1# telnet 100.100.100.18

Trying 100.100.100.18...

Connected to 100.100.100.18.

Escape character is '^]'.

h)

Verify the Telnet RASLog notification on RB2 through C1.

The RASLog message displays on the console.

RB2# 2012/05/10-17:31:09, [SEC-1203], 312942, M1, INFO, C1, Login

information: Login successful via TELNET/SSH/RSH. IP Addr: 2.2.2.1

i)

Verify the VCS fabric configuration on RB2 through C1.

The output is identical to the output generated in step 3d. The difference is that you are
now connected to RB2 through the in-band management interface.

RB2# show vcs

Config Mode : Local-Only

VCS ID : 2

Configuring In-Band Management

558

Network OS Administrator’s Guide

53-1003225-04