IAI America TT-C3 - Manual (Page 333)

323
INTELLIGENT ACTUATOR
Appendix
Appendix
(In the panel
wind
ow, the three di
gits after “E” in
dicate an error n
u
mber.)
Erro
r No.
Erro
r name
De
scription, a
c
tion, etc.
A44
Point-data
count specification error
The sp
ecified number of point data is invalid.
A45
Symbol-record count speci
fic
ation erro
r
The sp
ecifie
d
numbe
r of symbol records is invalid.
A46
Variabl
e-data count specification error
The specified number of variable data is
invalid.
A48
Erro
r-d
etail q
uery type 1 error
Error-detail query type 1 is invalid.
A49
Erro
r-d
etail q
uery type 2 error
Error-detail query type 2 is invalid.
A4A
Monitori
ng data type error
The data
type for monitoring data query is invalid.
A4B
Monitori
ng-re
cord co
unt sp
ecification error
The sp
ecified numbe
r of records for moni
toring data query is invalid.
A4C
Monitori
ng-operation
speci
al comm
and register busy erro
r
The drive
r sp
ecial
comm
a
nd ACK gen
e
rated a timeo
ut during
monitori
ng op
eration.
A4E
Parameter register busy error at
issuance of slave command
The driver
special
comm
and ACK generated a timeout at issuance o
f a
slave command.
A4F
Software
reset refusal error during operation
Software
reset (SIO) is prohibited during operation (program i
s
running,
servo i
s
in use, etc.).
A50
Drive-source
recovery request refusal error
The drive
-source
cutoff fact
or (error, dea
dman switch, safety gate,
emergency st
op, etc.) has
not been rem
oved.
A51
Operation-pause reset request ref
u
s
al error
The all-ope
ration-pause factor (drive-s
ource cutoff, operation-pause
signal, deadman switch,
safety gate, emergency
stop, etc.) has not
been removed.
A53
Refu
sal erro
r due to se
rvo ON
A processin
g not permitted
during servo
ON was attempted.
A54
Refu
sal erro
r due to un
sup
ported fun
ctio
n
The fun
ction is not su
pported.
A55
Refu
sal erro
r due to exclu
si
ve manufactu
rer fun
ction
A pr
ocessin
g not open
ed to
users othe
r than the man
u
facture
r was
attempted.
A56
Refusal error due to invalid data
The data is invalid.
A57
Program start
duplication error
An attempt was mad
e to st
art a pro
gra
m
currently run
ning.
A58
BCD error warning
The BCD value being
read may be invalid, or the value being
written
(variable 99) may be a neg
ative value, among other reasons.
A59
IN/OUT
com
mand po
rt flag error warni
ng
The num
ber of I/O ports (fl
ags) may hav
e exceeded 32, among other
reasons. Check the I/O
port (flag) specifi
cations.
A5B
C
h
ar
ac
ter-
s
tr
ing
o
value conversion e
rror wa
rni
ng
The sp
ecifie
d
numbe
r of co
nverting cha
racters i
s
invalid or characters
that cannot be converted to value are included.
A5C
Copying-character count
error warning with
SCPY command
The sp
ecifie
d
numbe
r of co
pying ch
ara
ct
ers i
s
invalid.
A5D
SCIF open e
rror in n
on-A
UTO mode
The ch
ann
el wa
s ope
ned i
n a non-A
UT
O mode. In the MANU mo
d
e, the
PC/TP connection must be forcibly
disconnected before openi
ng the
seri
al ch
ann
e
l opene
d to the use
r. Exerci
se caution.
A5E
I/O-port/flag count specifi
cation error
The sp
ecified number of I/O port
s/flags
is invalid.
A5F
Fieldbu
s e
rro
r (LERROR-ON
)
A LERRO
R-ON was d
ete
cted.
A60
Fieldbu
s e
rro
r (LERROR-BLINK)
A LERRO
R-B
LINK wa
s det
ected.