MITSUBISHI ELECTRIC Mitsubishi Programmable Logic Controller QD75D User Manual
Page 757
Index - 7
Multiple PLC .................................................... 2-5
Multiplying rate setting (Explanation of positioning
terms)................................................ Appendix-81
[N]
Names of each part......................................... 4-3
NC language (Explanation of positioning terms)
.......................................................... Appendix-81
Near pass function ...................................... 12-18
Near pass .................................................... 12-18
Near-point dog (Explanation of positioning terms)
.......................................................... Appendix-81
Near-point dog method machine OPR ........... 8-6
Near-point dog signal .................................... 3-20
New acceleration time value (
Cd.10
) ...... 5-116
New current value ......................................... 9-98
New current value ( Cd.9 )......................... 5-114
New current value (Explanation of positioning
terms)................................................ Appendix-81
New deceleration time value (
Cd.11
) ...... 5-116
New speed value (
Cd.14
) ........................ 5-118
New torque value (
Cd.22
)........................ 5-122
NEXT start ................................................... 10-15
No. of control axes .......................................... 3-2
No. of modules can be mounted..................... 2-5
No. of occupied I/O points............................... 3-3
No. of pulses per rotation ( Pr.2 ) ............... 5-20
No. of write accesses to flash ROM (
Md.19
)
....................................................................... 5-94
NOP instruction ........................................... 9-101
Normal start ................................................... 10-7
[O]
OP (Explanation of positioning terms)
.......................................................... Appendix-82
OP address (
Pr.45
)................................... 5-48
OP shift amount (
Pr.53
) ............................ 5-56
OP shift function ............................................ 12-8
OP shift function (Explanation of positioning terms)
.......................................................... Appendix-82
Operating principle .......................................... 1-7
Operation pattern ( Da.1 )............................ 5-60
Operation pattern (Explanation of positioning
terms) ............................................... Appendix-82
Operation patterns ...........................................9-5
Operation timing and processing time during
position-speed switching control ...................9-91
Operation timing and processing time during
speed-position switching control (ABS mode)
........................................................................9-91
Operation timing and processing time during
speed-position switching control (INC mode)
........................................................................9-84
Operation timing and processing time of fast OPR
........................................................................8-21
OPR acceleration time selection (
Pr.51
) ..5-54
OPR basic parameters ..................................5-46
OPR complete flag.......................................5-102
OPR deceleration time selection (
Pr.52
) ..5-54
OPR detailed parameters ..............................5-54
OPR direction (
Pr.44
) ................................5-48
OPR dwell time (
Pr.49
)..............................5-54
OPR method ....................................................8-5
OPR method (
Pr.43
)..................................5-46
OPR method (1): Near-point dog method.......8-6
OPR method (2): Stopper method 1) ..............8-8
OPR method (3): Stopper method 2) ............8-11
OPR method (4): Stopper method 3) ............8-14
OPR method (5): Count method 1)
........................................................................8-16
OPR method (6): Count method 2)
........................................................................8-18
OPR method (Explanation of positioning terms)
.......................................................... Appendix-82
OPR OFF request program ...........................6-12
OPR parameter (Explanation of positioning terms)
.......................................................... Appendix-82
OPR request ....................................................8-2
OPR request (Explanation of positioning terms)
.......................................................... Appendix-83
OPR request flag .........................................5-102
OPR request flag OFF request (
Cd.19
)
......................................................................5-122
OPR retry (
Pr.48
).......................................5-50
OPR retry function .........................................12-4