MITSUBISHI ELECTRIC Mitsubishi Programmable Logic Controller QD75D - Manual (Page 754)

Index - 4
DOS/V personal computer............................ A-13
Drive unit (Explanation of positioning terms)
.......................................................... Appendix-74
Drive unit (Servo amplifier) ........................... A-21
Drive unit READY.......................................... 3-21
Drive unit READY (Explanation of positioning
terms)................................................ Appendix-74
Droop pulse (Explanation of positioning terms)
.......................................................... Appendix-75
Dwell time (Explanation of positioning terms)
.......................................................... Appendix-75
Dwell time (JUMP destination positioning data
No.) ( Da.9 ).................................................. 5-70
Dwell time during OPR retry ( Pr.57 )......... 5-56
Dynamic brake (Explanation of positioning terms)
.......................................................... Appendix-75
[E]
Electrical specifications ................................. 3-17
Electromagnetic brake (Explanation of positioning
terms)................................................ Appendix-75
Electronic gear (Explanation of positioning terms)
.......................................................... Appendix-75
Electronic gear function............................... 12-13
Emergency stop ............................................ 6-42
Emergency stop (Explanation of positioning terms)
.......................................................... Appendix-75
Encoder (Explanation of positioning terms)
.......................................................... Appendix-75
Error and warning details .............................. 15-2
Error compensation method ....................... 12-14
Error correction (Explanation of positioning terms)
.......................................................... Appendix-76
Error detection signal .................................... 3-15
Error history ................................................... 5-92
Error history pointer ( Md.13 ) ...................... 5-92
Error judgement ( Md.7 ).............................. 5-90
Error reset (Explanation of positioning terms)
.......................................................... Appendix-76
Error reset program ....................................... 6-23
Execution data backup function.................... 13-5
Execution prohibition flag.............................. 3-14
External command ........................................ 3-21
External command function selection ( Pr.42 )
....................................................................... 5-42
External command function valid setting program
....................................................................... 6-12
External command valid ( Cd.8 )................5-114
External device connector ...............................4-3
External dimension drawing .......... Appendix-107
External input/output signal ( Md.30 ) ........5-100
External I/O signal logic switching function...13-7
External I/O signal monitor function ..............13-8
External regenerative brake resistor (Explanation
of positioning terms) ........................ Appendix-76
[F]
F (Explanation of positioning terms)
.......................................................... Appendix-76
Fast OPR........................................................8-20
Fast OPR (Explanation of positioning terms)
.......................................................... Appendix-76
Fatal stop........................................................6-42
Features of QD75 ............................................1-2
Feed pulse (Explanation of positioning terms)
.......................................................... Appendix-76
Feed screw (Explanation of positioning terms)
.......................................................... Appendix-76
Feedback pulse (Explanation of positioning terms)
.......................................................... Appendix-76
Feedrate ( Md.22 ) ........................................5-96
Fixed-feed (Explanation of positioning terms)
.......................................................... Appendix-77
Flash memory (Explanation of positioning terms)
.......................................................... Appendix-77
Flash ROM .......................................................7-2
Flash ROM write program .............................6-23
Flash ROM write request ( Cd.1 ) ..............5-110
Flat type motor (Pancake motor) (Explanation of
positioning terms)............................. Appendix-77
Flow of all processes .....................................1-15
Flow of system operation...............................1-15
FLS signal (Explanation of positioning terms)
.......................................................... Appendix-77
For creating program .......................................6-2
For installation..................................................4-7
For maintenance ............................................4-15
For restarting..................................................6-41
For starting "fast OPR" ..................................6-31
For starting "machine OPR" ..........................6-30
For starting "major positioning control" .........6-32
For starting "position-speed switching control"
........................................................................6-33