Altera IP Compiler for PCI Express - Manual (Page 256)

15–24 Chapter 15: Testbench and Design Example
Root Port Design Example
IP Compiler for PCI Express User Guide August 2014 Altera Corporation
■ _example_rp_pipen1b.v—the top-level of the root port design
example that you use for simulation. This module instantiates the root port IP
Compiler for PCI Express variation, .v, and the root port
application altpcietb_bfm_vc_intf_ast. This module provides both PIPE and serial
interfaces for the simulation environment. This module has two debug ports
named test_out_icm (which is the test_out signal from the IP core) and test_in
which allows you to monitor and control internal states of the IP Compiler for PCI
Express variation. (Refer to
“Test Signals” on page 5–58 .)
■ _example_rp_top.v—the top level of the root port example
design that you use for synthesis. The file instantiates
_example_rp_pipen1b.v. Note, however, that the synthesized
design only contains the IP Compiler for PCI Express variation, and not the
application layer, altpcietb_bfm_vc_intf_ast. Instead, the application is replaced
with dummy signals in order to preserve the variant's application interface. This
module is provided so that you can compile the variation in the Quartus II
software.
■ altpcietb_bfm_vc_intf_ast.v —a wrapper module which instantiates either
altpcietb_vc_intf_ast_64 or altpcietb_vc_intf_ast_128 based on the type of
Avalon-ST interface that is generated. It also instantiates the ECRC modules
altpcierd_cdma_ecrc_check
and altpcierd_cdma_ecrc_gen which are used when
ECRC forwarding is enabled.
■ altpcietb_vc_intf_ast_64.v and altpcietb_vc_intf_ast_128.v—provide the interface
between the IP Compiler for PCI Express variation and the root port BFM tasks.
They provide the same function as the altpcietb_vc_intf.v module, transmitting
PCI Express requests and handling completions. Refer to the
“Root Port BFM” on
page 15–26 for a full description of this function. This version uses Avalon-ST
signalling with either a 64- or 128-bit data bus to the IP Compiler for PCI Express
variation. There is one VC interface per virtual channel.
■ altpcietb_bfm_vc_intf_ast_common.v —contains tasks called by
altpcietb_vc_intf_ast_64.v and altpcietb_vc_intf_ast_128.v
■ altpcierd_cdma_ecrc_check.v —checks and removes the ECRC from TLPs
received on the Avalon-ST interface of the IP Compiler for PCI Express variation.
Contains the following submodules:
altpcierd_cdma_ecrc_check_64.v , altpcierd_rx_ecrc_64.v, altpcierd_rx_ecrc_64.vo,
altpcierd_rx_ecrc_64_altcrc.v , altpcierd_rx_ecrc_128.v, altpcierd_rx_ecrc_128.vo,
altpcierd_rx_ecrc_128_altcrc.v . Refer to the “Chaining DMA Design Example” on
page 15–6 for a description of these submodules
■ altpcierd_cdma_ecrc_gen.v —generates and appends ECRC to the TLPs
transmitted on the Avalon-ST interface of the IP Compiler for PCI Express
variation. Contains the following submodules:
altpcierd_cdma_ecrc_gen_calc.v , altpcierd_cdma_ecrc_gen_ctl_64.v,
altpcierd_cdma_ecrc_gen_ctl_128.v , altpcierd_cdma_ecrc_gen_datapath.v,
altpcierd_tx_ecrc_64.v , altpcierd_tx_ecrc_64.vo, altpcierd_tx_ecrc_64_altcrc.v,
altpcierd_tx_ecrc_128.v , altpcierd_tx_ecrc_128.vo, altpcierd_tx_ecrc_128_altcrc.v,
altpcierd_tx_ecrc_ctl_fifo.v , altpcierd_tx_ecrc_data_fifo.v,
altpcierd_tx_ecrc_fifo.v Refer to the “Chaining DMA Design Example” on
page 15–6 for a description of these submodules.