List of figures – Teledyne 6200E - Sulfides Analyzer User Manual
Page 9
Model 6200E Instruction Manual
M6200E Rev: A1
9
LIST OF FIGURES
Figure 3-1: Location of Shipping Screws .......................................................................... 22
Figure 3-2: Rear Panel Layout ........................................................................................ 23
Figure 3-3: Analog Output Connector .............................................................................. 24
Figure 3-4: Status Output Connector............................................................................... 25
Figure 3-5: Control Input Connector................................................................................ 26
Figure 3-6: Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ........... 28
Figure 3-7: Pneumatic Connections–Basic Configuration–Using Bottled Span Gas .................. 28
Figure 3-8: Basic Pneumatic Connections for Units with Valve Options ................................. 30
Figure 3-9: M6200E Layout (with IZS) ............................................................................ 31
Figure 3-10: Front Panel Layout ....................................................................................... 34
Figure 3-11: Pneumatic Diagram of the M6200E Standard Configuration. ............................... 37
Figure 5-1: Current Loop Option Installed on the Motherboard ............................................ 46
Figure 5-4: M6200E Multidrop Card................................................................................. 53
Figure 5-5: M6200E Ethernet Card.................................................................................. 54
Figure 5-6: M6200E Rear Panel with Ethernet Installed...................................................... 54
Figure 6-1: Front Panel Display ...................................................................................... 59
Figure 6-2 Viewing M6200E TEST Functions .................................................................... 62
Figure 6-3 Viewing and Clearing M6200E WARNING Messages ........................................... 64
Figure 6-4: Analog Output Connector Key ........................................................................ 70
Figure 6-5: Setup for Calibrating Analog Outputs .............................................................. 90
Figure 6-6: Setup for Calibrating Current Outputs ............................................................. 92
Figure 6-7: Back Panel connector Pin-Outs for COM1 & COM2 in RS-232 mode.................... 103
Figure 6-8: CPU connector Pin-Outs for COM1 & COM2 in RS-232 mode. ............................ 104
Figure 6-9: CPU card Locations of RS-232/486 Switches, Connectors and Jumpers .............. 105
Figure 6-10: Back Panel connector Pin-Outs for COM2 in RS-485 mode. ............................... 106
Figure 6-11: CPU connector Pin-Outs for COM2 in RS-485 mode. ........................................ 106
Figure 6-12: Location of JP2 on RS232-Multidrop PCA (option 62) ...................................... 113
Figure 6-13: RS232-Multidrop PCA Host/Analyzer Interconnect Diagram .............................. 115
Figure 6-14: Default iDAS Channels Setup ....................................................................... 124
Figure 6-15: APICOM user interface for configuring the iDAS. ............................................. 137
Figure 6-16: iDAS Configuration Through a Terminal Emulation Program.............................. 138
Figure 6-17: Status Output Connector............................................................................. 139
Figure 6-18: Control Inputs with local 5 V power supply..................................................... 141
Figure 6-19: Control Inputs with external 5 V power supply................................................ 141
Figure 6-20: APICOM Remote Control Program Interface.................................................... 148
Figure 7-2: Setup for Manual Calibration with Z/S Valve Option Installed............................ 164
Figure 7-4: Typical Setup for Manual Calibration of M6200E in Multigas Measurement Mode .. 172
Figure 9-1: Sample Particulate Filter Assembly ............................................................... 193
Figure 9-2: Zero Air Scrubber Assembly ........................................................................ 196
Figure 9-3: H
2
S Æ SO
2
Converter Assembly ................................................................... 199
Figure 9-4: Critical Flow Orifice Assembly ...................................................................... 201
Figure 10-1: UV Absorption ........................................................................................... 205
Figure 10-2: UV Light Path ............................................................................................ 207
Figure 10-3: Source UV Lamp Construction ...................................................................... 208
Figure 10-4: Excitation Lamp UV Spectrum Before/After Filtration ....................................... 209
Figure 10-5: PMT Optical Filter Bandwidth........................................................................ 209
Figure 10-6: Effects of Focusing Source UV in Sample Chamber .......................................... 210
Figure 10-7: M6200E Gas Flow and Location of Critical Flow Orifice ..................................... 213