Teledyne 6200E - Sulfides Analyzer - Manual (Page 175)

Model 6200E Instruction Manual Calibration Procedures
M6200E Rev: A1 175
Toggle keys
to set
number of
days
between
procedures
(1-367)
Toggle keys
to set
delay time for
each iteration
of the
sequence:
HH:MM
(0 – 24:00)
SETUP X.X DELTA D AYS: 1
EDIT EXIT
SETUP X.X DELTA DAYS: 1
0 0 2 ENTR EXIT
SETUP X.X DELTA DAYS:2
SET> EDIT EXIT
SETUP X.X DELTA TIM E00:00
EDIT EXIT
SETUP X.X DELTA TIME: 00:00
0 0 :3 0 ENTR EXIT
SETUP X.X DELTA TIEM:00:30
SET> EDIT EXIT
SETUP X.X STARTING TIM E:14:15
SET> EDIT EXIT
EXIT returns
to the SETUP
Menu
SETUP X.X DURATION:15.0 M INUTES
EDIT EXIT
SETUP X.X DURATION 15.0MINUTES
3 0 .0 ENTR EXIT
SETUP X.X DURATION:30.0 M INUTES
SET> EDIT EXIT
Toggle keys
to set
duration for
each
iteration of
the
sequence:
Set in
Decimal
minutes
from
0.1 – 60.0
SETUP X.X CALIBRATE: OFF
EDIT EXIT
SETUP X.X C ALIBRAT E: OFF
ON ENTR EXIT
SETUP X.X CALIBRATE: ON
EDIT
EXIT
Toggle key
between
Off and
ON
SETUP X.X SEQ 2) ZERO–SPAN, 2:00:30
PREV NEXT
MODE SET EXIT
Sequence Delta Time
MODE Delta Days
SAMPLE ENTER SETUP PASS : 818
8 1 8 ENTR EXIT
SETUP X.X PRIMARY SETUP MENU
CFG
AC AL DAS RNGE PASS CLK MORE EXIT
SETUP X.X SEQ 1) DISABLED
NEXT MODE EXIT
SETUP X.X SEQ 2) DISABLED
PREV NEXT
M ODE EXIT
SETUP X.X M ODE: DISABLED
NEXT ENTR EXIT
SETUP X.X MODE: ZERO
PREV
NEXT ENTR EXIT
SETUP X.X M ODE: ZERO–SPAN
PREV
NEXT ENTR EXIT
SETUP X.X SEQ 2) ZERO–SPAN, 1:00:00
PREV NEXT
MODE SET EXIT
SETUP X.X TIM ER ENABLE: ON
SET> EDIT EXIT
SETUP X.X STARTING DATE: 01–JAN–02
EDIT EXIT
SETUP X.X STARTING DATE: 01–JAN–02
0 4 SEP 0 3 ENTR EXIT
Toggle keys
to set
day, m onth &
year:
Form at :
DD-MON-Y Y
SETUP X.X STARTING DATE: 04–SEP–03
SET> EDIT EXIT
Default
value is
ON
SETUP X.X STARTING DATE: 04–SEP–03
SET> EDIT EXIT
SETUP X.X STARTING TIM E:00:00
EDIT EXIT
SETUP X.X STARTING TIM E:00:00
1 4 : 1 5 ENTR EXIT/
Toggle keys to
set time:
Format : HH:MM
This is a 24 hr
clock .
PM hours are
13 – 24.
Example
2:15 PM = 14:15
SAMPLE RANGE = 500.0 PPB H2S =XXX.X
< TST TST > CAL CALZ CALS
SETUP
With dynamic calibration turned on, the state of the internal setup variables DYN_SPAN and
DYN_ZERO is set to ON and the instrument will reset the slope and offset values for the H
2
S
response each time the AutoCal program runs. This continuous re-adjustment of calibration
parameters can often mask subtle fault conditions in the analyzer. It is recommended that, if
dynamic calibration is enabled, the analyzer’s test functions, slope and offset values be checked
frequently to assure high quality and accurate data from the instrument.