Teledyne 6200E - Sulfides Analyzer User Manual
Page 11

Model 6200E Instruction Manual
M6200E Documentation
M6200E Rev: A1
11
Table 6-11: Analog Output Pin Assignments ....................................................................... 85
Table 6-12: Voltage Tolerances for Analog Output Calibration ............................................... 89
Table 6-13: Current Loop Output Calibration with Resistor ................................................... 93
Table 6-14: Test Parameters Available for Analog Output A4 .............................................. 100
Table 6-15: Ethernet Status Indicators ............................................................................ 107
Table 6-16: LAN/Internet Configuration Properties ............................................................ 108
Table 6-17: Internet Configuration Keypad Functions ........................................................ 113
Table 6-18: COMM Port Communication modes................................................................. 116
Table 6-19: Front Panel LED Status Indicators for iDAS ..................................................... 120
Table 6-20: iDAS Data Channel Properties ....................................................................... 121
Table 6-21: iDAS Data Parameter Functions..................................................................... 122
Table 6-22: Status Output Pin Assignments...................................................................... 140
Table 6-23: Control Input Pin Assignments....................................................................... 141
Table 6-24: Terminal Mode Software Commands .............................................................. 142
Table 6-25: Command Types ......................................................................................... 143
Table 6-26: Serial Interface Documents........................................................................... 148
Table 6-27: RS-232 Communication Parameters for Hessen Protocol ................................... 149
Table 6-28: M6200E Hessen Protocol Response Modes....................................................... 151
Table 6-29: Default Hessen Status Bit Assignments........................................................... 154
Table 7-1: NIST-SRM's Available for Traceability of H
2
S and SO
2
Calibration Gases ............... 159
Table 7-2: AutoCal Modes............................................................................................ 173
Table 7-3: AutoCal Attribute Setup Parameters............................................................... 173
Table 7-4: Example Auto-Cal Sequence ......................................................................... 174
Table 7-5: Calibration Data Quality Evaluation................................................................ 177
Table 8-1: Activity Matrix for Calibration Equipment & Supplies......................................... 180
Table 8-2: Activity Matrix for Calibration Procedure ......................................................... 180
Table 8-3: Activity Matrix ............................................................................................ 182
Table 8-4: Definition of Level 1 and Level 2 Zero and Span Checks .................................... 183
Table 9-1: M6200E Preventive Maintenance Schedule ...................................................... 190
Table 9-2: Predictive Uses for Test Functions.................................................................. 192
Table 10-1: M6200E Multigas Valve Cycle-Phases ............................................................. 214
Table 10-2: Relay Board Status LED’s ............................................................................. 227
Table 10-3: Front Panel Status LED’s .............................................................................. 233
Table 11-1: Warning Messages - Indicated Failures ........................................................... 241
Table 11-2: Test Functions - Possible Causes for Out-Of-Range Values................................. 243
Table 11-3: Relay Board Status LEDs .............................................................................. 246
Table 11-4: DC Power Test Point and Wiring Color Code .................................................... 253
Table 11-5: DC Power Supply Acceptable Levels ............................................................... 254
Table 11-6: Relay Board Control Devices ......................................................................... 255
Table 11-7: Analog Output Test Function - Nominal Values................................................. 256
Table 11-8: Status Outputs Check Pin Out ....................................................................... 256
Table 12-1: Static Generation Voltages for Typical Activities ............................................... 266
Table 12-2: Sensitivity of Electronic Devices to Damage by ESD ......................................... 266
Table A-1: M6200E Setup Variables, Revision A.1 ........................................................... 283
Table A-2: M6200E Warning Messages, Revision A.1 ....................................................... 290
Table A-3: M6200E Test Functions, Revision A.1 ............................................................. 291
Table A-4: M6200E Signal I/O Definitions, Revision A.1 ................................................... 292
Table A-5: M6200E DAS Trigger Events, Revision A.1 ...................................................... 296
Table A-6: M6200E iDAS Functions, Revision A.1 ............................................................ 297
Table A-7: Terminal Command Designators, Revision A.1................................................. 298
Table A-8: Terminal Key Assignments, Revision A.1 ........................................................ 299
Table B-1: M6200E Spare Parts List .............................................................................. 301
Table D-1: List of Included Electronic Schematics............................................................ 305