Luminex 100 IS Version 2.2 - Manual (Page 12)

viii PN 89-00002-00-069 Rev. A
Luminex 100 IS User Manual Version 2.2 x MAP Technology
Running: Sheath Empty. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Sample Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Insufficient Bead Count. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Temperature Divergence from Calibration Temperature . 8-8
Failed Control in Batch . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Failed Curve Fit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Sample High/Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Sample Timed Out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Sample Empty Detected . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Unknown Formula Failure . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Luminex 100 Analyzer Problems . . . . . . . . . . . . . . . . . . . . . 8-10
Power On Indicator Light Is Not On . . . . . . . . . . . . . . . . 8-10
PC Is Not Powered On . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Sheath Fluid Is Leaking Onto the Plate Holder. . . . . . . . 8-10
Progress Bar Indicates No Events Being Collected
During Calibration or Verification . . . . . . . . . . . . . . . . . 8-10
Luminex XYP instrument Problems . . . . . . . . . . . . . . . . . . . 8-11
Power On Indicator Light Is Not On . . . . . . . . . . . . . . . . 8-11
Heater Block Will Not Reach Desired Temperature. . . . 8-11
There Is a Grinding Noise When the Plate Carrier
Moves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Product Numbers 9-1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
xMAP Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Installation A-1
Assemble and Power up System. . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Connect the Luminex XYP Instrument and the
Luminex 100 Analyzer to the PC . . . . . . . . . . . . . . . . . . . A-1
Install and Replace the Luminex XYP Instrument
Sample Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Configure the Luminex 100 IS 2.2 Software . . . . . . . . . . A-9
Enter Target Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Adjust the Sample Probe Vertical Height . . . . . . . . . . . . A-10
Install the Luminex XYP Instrument Reservoir . . . . . . . A-11
Install the Luminex XYP Instrument Heater
Block (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
Luminex 100 IS 2.2 Software Installation . . . . . . . . . . . . . . . . . . A-13
Network Installation Advisory. . . . . . . . . . . . . . . . . . . . . . . . A-15
Prepare System for First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Installation Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16
Glossary B-1