Lenze 8200 motec frequency inverter 0.25kW-7.5kW - Manual (Page 233)

Appendix
Code table
14−32
L
EDB82MV752 EN 5.2
Code IMPORTANT Possible settings
No. Selection Lenze Name
C0351*
v
System bus baud
rate 0 0 500 kbit/s
·
Only for the E82ZAFCC system bus
function module on the FIF interface.
·
Changes will become effective after the
command "reset node"
During operation with 217x
communication modules the baud rate
must be set under C0125.
1 250 kbits/s
2 125 kbits/s
3 50 kbits/s
4 1000 kbits/s (only E82ZAFCC100 function
module)
5 20 kbits/s
C0352*
v
Configuration of
system bus devices 0 0 slave
·
Only for the E82ZAFCC system bus
function module on the FIF interface.
·
Changes will become effective after the
command "reset node"
1 Master
C0353*
V
Source of system
bus address 0
1 C0350 is the source
C0354 is the source
·
Only for E82ZAFCC system bus function
module on FIF interface.
·
Source of the address for system bus
process data channels
1 CAN1 (Sync) 0 Effective for sync control (C0360 = 1)
2 CAN2 0
3 CAN1 (time) 0 Effective for event or time control (C0360 =
0)
C0354*
v
Selective system
bus address 0 {1} 513
·
Only for the E82ZAFCC system bus
function module on the FIF interface.
·
Individual addressing of system bus
process data objects
1 CAN−IN1 (sync) 129 Effective with sync control (C0360 = 1)
2 CAN−OUT1 (sync) 1
3 CAN−IN2 257
4 CAN−OUT2 258
5 CAN−IN1 (time) 385 Effective with event and time control
(C0360 = 0)
6 CAN−OUT1 (time) 386
C0355*
v
System bus
identifier 0 {1} 2047
·
Only for the E82ZAFCC system bus
function module on the FIF interface.
·
Only display
1 CAN−IN1 Identifier of CAN1 with sync control (C0360
= 1)
2 CAN−OUT1
3 CAN−IN2
4 CAN−OUT2
5 CAN−IN1 Identifier of CAN1 with event or time control
(C0360 = 0)
6 CAN−OUT1
C0356*
v
System bus time
settings 0 {1 ms} 65000 Only for E82ZAFCC system bus function
module on FIF interface.
1 boot up 3000 Required for CAN system without master
2 Cycle time
CAN−OUT2
0 0 = event−controlled process data transfer
> 0 = cyclic process data transfer
3 Cycle time
CAN−OUT1
0 0 and C0360 = 0: event−controlled process
data transfer
> 0 and C0360 = 1: cyclic process data
transfer
4 CAN delay 20 Waiting time until cyclic transmission starts
after boot−up
C0357*
v
System bus
monitoring times 0 = monitoring
inactive {1 ms} 65000 Only for E82ZAFCC system bus function
module on FIF interface.
1 CAN−IN1 (Sync) 0 active if C0360 = 1
TRIP CE1 in case of communication fault
2 CAN−IN2 0 TRIP CE2 in case of communication fault
3 CAN−IN1 (time) 0 active if C0360 = 0
TRIP CE3 in case of communication fault