Lenze 8200 motec frequency inverter 0.25kW-7.5kW - Manual (Page 262)

Table of keywords
abc
15−1
L
EDB82MV752 EN 5.2
15 Table of keywords
0 ... 9
87 Hz technology, 7−6
A
AC motor braking, 7−31
Acceleration, 7−24
Acceleration time
Additional setpoint , 7−24 , 14−26
Minimum frequency limitation, 7−21 , 14−27
Process controller setpoint, 14−27
Acceleration times, 7−24
Accessories, 12−1
External brake resistor, 11−1
Acknowledgement
negative, 6−16
positive, 6−16
Actual value, Digital supply, 7−39
Actual value selection, 7−32
PID controller, 7−54
Address settings, by DIP switch, 4−10 , 4−14 , 4−15
Adjustment
Bipolar setpoint, 7−36
Inverse setpoint, 7−37
Unipolar setpoint, 7−36
AIF, 1−1
Analog input 1
Gain, 7−34 , 14−16
Offset, 7−34 , 14−16
Analog input signals, 7−57
Analog inputs
Automatic adjustment, 7−35 , 14−49
gain, 7−34 , 14−38
offset, 7−34 , 14−38
Analog output 1
Gain, 7−61 , 14−19
Offset, 7−61 , 14−19
Analog output signals, 7−59
Analog outputs, Configuration, 7−59
Analog process data output words, Configuration, 7−64
Appendix, 14−1
Application as directed, 1−2
Application datum, Display, 7−86
Application examples, 13−1
group drive, 13−13
operation of mid−frequency motors, 13−9
power control, 13−15
pressure control, 13−1
setpoint summation, 13−14
speed control, 13−10
Application I/O
acceleration times − main setpoint, 7−24 , 14−19
additional JOG values, 7−43 , 14−49
Automatic analog input adjustment, 7−35 , 14−49
Automatic frequency input adjustment , 7−40 , 14−49
Calibration of process variable, 7−88 , 14−49
deceleration times − main setpoint, 7−24 , 14−19
Delay digital outputs, 14−48
delay of digital outputs, 7−76
Main and additional setpoint, 14−26
Offset of analog outputs, 7−62 , 14−47
output signal range − analog outputs, 7−62 , 14−48
Setpoint selection range, 7−34 , 14−16
terminal assignment, 4−12
Approvals, 3−1
Asynchronous standard motors, 1−2
Auto−TRIP reset, 8−7
Automation, 9−1
with INTERBUS, PROFIBUS−DP, LECOM−B (RS485), 9−1
B
Bar graph display, 6−3
Basic settings, Own, 7−92 , 14−12
Baud rate, 14−21
LECOM−A (RS232) communication module, 6−10
Bipolar setpoint, Adjustment, 7−36
Brake chopper, switching threshold, 14−25
Brake resistor, 11−3
selection, 11−1
Brake transistor, 11−2
Brakes, 11−1
Braking, 7−24
Braking operation, 11−1
With external brake resistor, 11−1
without additional measures, 11−1
Bus function modules, terminal assignment, 4−16
Bus systems, Setpoint selection, 7−46
C
Cable cross−sections
operation with increased rated power
230 V, 3−6