Lenze 8200 motec frequency inverter 0.25kW-7.5kW - Manual (Page 222)

Appendix
Code table
14−21
L
EDB82MV752 EN 5.2
Code IMPORTANT Possible settings
No. Selection Lenze Name
C0114
v
Level inversion −
digital inputs 0 0 Level inversion switched off
·
By entering the sum of the selected
values you can invert several inputs.
·
C0114 and C0411 are the same
·
The "Change over parameter set"
cannot be inverted!
1 E1 inverted
2 E2 inverted
4 E3 inverted
8 E4 inverted
16 E5 inverted Only application I/O
32 E6 inverted Only application I/O
64 T1/T2 inverted Only connect potential−free switches to
T1/T2.
T1/T2 is active when the switch is open.
C0117
v
Fixed configuration
of digital output A1
(DIGOUT1) 0 Changes of C0117 will be copied to
C0415/2. Free configuration under
C0415/2 sets C0117 =255!
^ 7−73
0 ... 16 see C0008
255 Free configuration under C0415/2 Only display
Do not change C0117 since settings under
C0415/2 can be lost
C0119
v
−25−
Configuration of
motor temperature
monitoring (PTC
input) / earth fault
detection 0 0 PTC input not active Earth fault detection
active
·
Signal output configuration under C0415
·
If several parameter sets are used, the
monitoring must be separately adjusted
for each parameter set.
·
Deactivate the earth fault detection, if it
has been activated unintentionally.
·
If the earth fault detection is active, the
motor starts after controller enable with
a delay of approx.40 ms.
^ 7−84
1 PTC input active,
TRIP set
2 PTC input active,
Warning set
3 PTC input not active Earth fault detection
inactive
4 PTC input active,
TRIP set
5 PTC input active,
Warning set
C0120 I 2 t switch−off 0 0
= not active {1 %} 200 Reference: Apparent motor current (C0054)
Ref. to active motor current (C0056)
possible, see C0310
^ 7−82
C0125*
v
Baud rate 0 LECOM System bus (CAN) 217x Only for communication modules on the AIF
interface:
·
LECOM−A (RS232) E82ZBL
·
LECOM−A/B/LI 2102
·
System bus (CAN) 217x
During operation with the E82ZAFCC
system bus function module the baud
rate must be set under C0351.
0 9600 baud 500 kbaud
1 4800 baud 250 kbaud
2 2400 baud 125 kbaud
3 1200 baud 50 kbaud
4 19200 baud 1000 kbaud
C0126*
v
Response in the
event of a
communication
error 10 Monitored communication channel By entering the sum of the selected values
you can activate a monitoring combination
0 All monitoring is deactivated
1 Process channel of the AIF interface Communication abort at active monitoring
activates TRIP CE0
2 Internal communication between function module
on FIF and controller Communication abort at active monitoring
activates TRIP CE5
4 Communication (bus OFF) at operation with
system bus function module (CAN) on FIF Communication abort at active monitoring
activates TRIP CE6
8 Remote parameter setting via C0370 at operation
with function module system bus (CAN) on FIF Communication abort at active monitoring
activates TRIP CE7
C0127
v
Setpoint selection 0 0 Absolute setpoint selection in Hz via C0046 or
process data channel
1 Setpoint selection normalised via C0141 (0... 100
%) or process data channel (
±16384 = C0011)
C0128 Service code Modifications only by Lenze Service!