SkyTrak 8042 Service Manual - Manual (Page 53)

General Information and Specifications
2.28 Model 8042, 10042, 10054 Legacy Rev. 10/03
2.6 FLUIDS, LUBRICANTS AND
CAPACITIES
2.6.1 Axle (Differential Housing)
a. Axle Differential Housing Lubricants
In general, use a Universal Tractor Fluid that meets the
following specifications:
Nominal viscosity at 104° F (40° C)....................... 55 cSt
Minimum viscosity at 212° F (100° C) .................. 9.1 cSt
Pour point (Maximum) .............................. -32° F (-36° C)
Flash point (Minimum) ............................ 392° F (200° C)
Minimum viscosity index............................................ 135
Products known to meet these requirements include:
• JOHN DEERE: JDM J20C (HY-GARD)
• FORD/NEW HOLLAND: ESN-M2C134-D
(Hydraulic Oil 134)
• MASSEY-FERGUSON: M-1141
(PERMANTRAN III)
• CHEVRON: CHEVRON 1000 THF
b. Axle Differential Housing Capacity
Axle differential housing (front axle) ........9.5 qt (9 liters)
Axle differential housing (rear axle) .....10.6 qt (10 liters)
2.6.2 Axle Wheel Ends
a. Axle Wheel End Lubricants
In general, use a Universal Tractor Fluid that meets the
following specifications:
Nominal viscosity at 104° F (40° C)....................... 55 cSt
Minimum viscosity at 212° F (10° C) .................... 9.1 cSt
Pour point (Maximum) .............................. -32° F (-36° C)
Flash point (Minimum) ............................ 392° F (200° C)
Minimum viscosity index............................................ 135
Products known to meet these requirements include:
• JOHN DEERE: JDM J20C (HY-GARD)
• FORD/NEW HOLLAND: ESN-M2C134-D
(Hydraulic Oil 134)
• MASSEY-FERGUSON: M-1141
(PERMANTRAN III)
• CHEVRON: CHEVRON 1000 THF
DO NOT add additional friction modifier to factory-filled
wheel ends. All wheel ends are factory-filled by the
manufacturer with oil. If a wheel end is drained for service, it
should be refilled with the gear oils listed.
Note: DO NOT use synthetic oil without the express
written consent of the manufacturer.
b. Axle Wheel End Capacity
The capacity listed below is for one wheel end
Axle wheel end (front axle)................... 1.7 qt (1,6 liters)
Axle wheel end (rear axle) ................... 1.3 qt (1,2 liters)
2.6.3 Transmission
a. Transmission Lubricants
In general, use a Universal Tractor Fluid that meets the
following specifications:
Nominal viscosity at 10° F (40° C) ........................ 55 cSt
Minimum viscosity at 212° F (100° C) .................. 9.1 cSt
Pour point (Maximum).............................. -32° F (-36° C)
Flash point (Minimum).............................392° F (200° C)
Minimum viscosity index ............................................135
Products known to meet these requirements include:
• JOHN DEERE: JDM J20C (HY-GARD)
• FORD/NEW HOLLAND: ESN-M2C134-D
(Hydraulic Oil 134)
• MASSEY-FERGUSON: M-1141
(PERMANTRAN III)
• CHEVRON: CHEVRON 1000 THF
b. Transmission Capacity
Capacity w/filter change ...................... 3 gal (11,8 liters)
Filter ........................................................ 1 qt (0,9 liters)