Sony GP-X1EM Grip Extension - Manual (Page 366)

366
1
Select the macro attachment register.
For details about the method of operation, see
“Setting the register to assign in a macro attachment”
(page 365).
2
To set to pre-macro mode, press and hold the [PRE
MACRO] button in the cross-point pad and press a 3rd
row cross-point button. To set to post-macro mode,
use the [POST MACRO] button instead.
The selected cross-point button blinks amber, and the
register set in step
1 is assigned to the button.
If you make both pre macro and post macro
settings for the same button
The latter setting is enabled.
To disable a button function when a macro
attachment is set
When a macro attachment is assigned to a button, you can
configure it so that the button function is not executed.
For details, see “Setting the Macro Operation Mode”
(page 434).
To set a macro attachment in macro only mode
1
Select the macro attachment register.
For details about the method of operation, see
“Setting the register to assign in a macro attachment”
(page 365).
2
Press and hold the [PRE MACRO] and [POST
MACRO] buttons at the same time in the cross-point
pad and press a 3rd row cross-point button.
The selected cross-point button blinks green, and the
register set in step
1 is assigned to the button.
To check macro attachment settings
Press and hold the [PRE MACRO] button or [POST
MACRO] button. While the button is pressed, the buttons
for which a macro attachment is set blink as follows.
While the [PRE MACRO] button is pressed:
• Buttons set in pre-macro mode: Blink amber
• Buttons set in macro only mode: Blink green
While the [POST MACRO] button is pressed:
• Buttons set in post-macro mode: Blink amber
• Buttons set in macro only mode: Blink green
Setting a macro attachment to a fader lever
You can set a macro attachment to any particular position
of a fader lever in the transition control block.
• In macro only mode, it is not possible to set a macro
attachment.
• On a split fader, you can set a macro attachment to the
main fader lever (for background A bus).
1
Select the macro attachment register.
For details about the method of operation, see
“Setting the register to assign in a macro attachment”
(page 365).
2
Move the fader lever to the position where you want to
set the macro attachment.
3
Press and hold the [PRE MACRO] button or [POST
MACRO] button
1)
in the cross-point pad, and press the
[PRIOR SET] button or [LIMIT SET] button in the
control block containing the fader lever operated in
step
2 .
1) Only when setting a macro attachment to the start point or end point
of fader lever operation, the use of the [PRE MACRO] and [POST
MACRO] buttons is different.
• To set the operation start point (0%): Press and hold the [PRE
MACRO] button.
• To set the operation end point (100%): Press and hold the [POST
MACRO] button.
This assigns the register set in step 1 to the fader lever
position selected in step 2 .
To check macro attachment settings
Press and hold the [PRE MACRO] button or [POST
MACRO] button. While the button is pressed, the fader
lever position where the macro attachment is set appears in
the following places.
Transition indicator in the transition execution section:
The indicator lights at the position where the macro
attachment is set.
Transition rate indication in the transition execution
section: This shows the fader lever position where the
macro attachment is set, as a percentage value (fader
lever start position as 0%, end position 100%).
Removing macro attachment settings
To cancel a macro attachment to a button
Press and hold the [PRE MACRO] or [POST MACRO]
button in the cross-point pad and press the blinking 3rd
row cross-point button. The macro attachment setting is
canceled.
To cancel a macro attachment to a fader lever
Press and hold the [PRE MACRO] button or [POST
MACRO] button in the cross-point pad, and press the
[PRIOR SET] button or [LIMIT SET] button in the control
block containing the fader lever with the macro
attachment.
Notes