beautypg.com

Sony 100M28 User Manual

Sony Photo Accessories

background image

1:5

1:3

1:7

1:5

7

6

8

1

2

3

4

5

1

2

3

4

5

6

8

–1

(1)

(2)

English

This manual is for use with several different lenses.
This lens is designed for Sony

cameras.

WARNING

To reduce fire or shock hazard, do not expose the unit to rain or moisture.
Do not directly look at the sun through this lens.
Doing so might harm your eyes or cause loss of eyesight.
Keep the lens out of reach of small children.
There is danger of accident or injury.

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other
European countries with separate collection
systems)
This symbol on the product or on its packaging indicates that
this product shall not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information
about recycling of this product, please contact your local Civic Office, your
household waste disposal service or the shop where you purchased the
product.

For the customers in the U.S.A.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.

CAUTION

You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Notes on use

• Do not leave the lens in direct sunlight. If sunlight is focused onto a nearby

object, it may cause a fire. If circumstances necessitate leaving the lens in direct
sunlight, be sure to attach the lens cap.

• Be careful not to subject the lens to mechanical shock while attaching it.
• Always place the lens caps on the lens when storing.
• Do not keep the lens in a very humid place for a long period of time to prevent

mold.

• After attaching the lens, do not carry the camera by holding the lens.
• Do not touch the lens contacts. If dirt, etc., gets on the lens contacts, it may

interfere or prevent the sending and receiving of signals between the lens and the
camera, resulting in operational malfunction.

Precaution for flash use
With certain of lens/flash combinations, the lens may partially block the light
of the flash, resulting in a shadow at the bottom of the picture. When using a
built-in camera flash, make sure to remove the lens hood and shoot from at
least 1m (3.3feet) away from your subject.

Vignetting
When you use lens, the corners of the screen become darker than the center.
To reduce this phenomena (called vignetting), close the aperture by 1 to 2
stops.

Condensation
If your lens is brought directly from a cold place to a warm place,
condensation may appear on the lens. To avoid this, place the lens in a plastic
bag or something similar. When the air temperature inside the bag reaches
the surrounding temperature, take the lens out.

Cleaning the lens
• Do not touch the surface of the lens directly.
• If the lens gets dirty, brush off dust with a lens blower and wipe with a soft,

clean cloth (Cleaning Cloth KK-CA (optional) is recommended).

• Do not use any organic solvent, such as thinner or benzine, to clean the lens or

the camera cone.

Names of parts

1…Focusing ring 2…Distance index 3…Lens contacts 4…Depth-of-field
scale 5…Distance scale 6…Focus-hold button 7…Focus-range limiter

*

8…Mounting index
* 50mm F2.8 Macro, 100mm F2.8 Macro only

Attaching/detaching the lens

To attach the lens (See illustration

-.)

1

Remove the rear and front lens caps and the camera body

cap.
• You can attach/detach the front lens cap in two ways, (1) and (2). When you

attach/detach the lens cap with the lens hood attached, use method (2).

2

Align the orange index on the lens barrel with the orange

index on the camera (mounting index), then insert the lens
into the camera mount and rotate it clockwise until it locks.
• Do not press the lens release button on the camera when mounting the lens.
• Do not mount the lens at an angle.

To remove the lens (See illustration

-.)

While pressing and holding the lens release button on the
camera, rotate the lens counterclockwise until it stops, then
detach the lens.

Attaching lens hood

It is recommended that you use a lens hood to reduce flare and ensure
maximum image quality.
* The 50mm F2.8 Macro does not include an external lens hood. The lens barrel

functions as a lens hood by design.

100mm F2.8 Macro:
Fit the hood into the mount on the end of the lens barrel and
rotate the hood clockwise until it clicks.
35mm F1.4 G:
Align the red line on the lens hood with the red dot on the lens.
Turn the hood clockwise until the red dot on the hood meets the
red dot on the lens and it clicks into place.
• When using a built-in camera flash, make sure to remove the lens hood to avoid

blockage of the flash light.

• If a marking (red line, red dot, etc.) is provided, attach the lens hood properly.

Otherwise, the lens hood may interfere with the desired effect or may appear in
pictures.

• When storing, turn over the lens hood and place it onto the lens backwards.

Focusing

When using the auto focus, the camera focuses the lens automatically.
When focusing manually, set your camera to the manual focus and rotate the
focusing ring while looking through the viewfinder. The focus signal in the
viewfinder indicates the current degree of the focus.
• The focusing ring can be rotated slightly past the infinity to provide accurate

focusing under various operating temperatures. Do not rotate the focusing ring
all the way to the end when focusing manually even at infinity. Look through the
viewfinder and set the focus precisely.

Focus-hold button

–(2)

While the focus-hold button is pressed, auto focus function is suspended and
the focus is fixed for shooting.
• The function of the focus-hold button can be changed on cameras with custom

function capability. Refer to the camera manuals for details.

Focus-range limiter

–(3)

For quick focusing, the focusing range can be limited to close or far range,
depending on the distance to your subject.

Close-focusing range

Far-focusing range

50mm F2.8 Macro

20 - 27cm

30cm -

100mm F2.8 Macro

35 - 54cm

59cm -

To focus on subjects at close range (see the table above), set focus anywhere
near the subject and then set the focus-range limiter to LIMIT; the focusing
range is limited to Close-focusing range. Likewise, when shooting subjects
at far range, set the focus anywhere near the subject and then set the focus-
range limiter to LIMIT; the focus range is limited to Far-focusing range. Set
the focus-range limiter to FULL to allow the entire focusing range.
• Set the focus-range limiter to FULL, when shooting a subject between the Close

and Far focusing ranges.

Depth-of-field scale

When focus is set on a subject, anything at that same distance will appear
sharp, and anything within a certain range before and beyond the subject will
also appear in focus; this is called depth of field. Depth of field depends on
the subject distance and aperture you choose and is indicated by the lines on
the depth-of-field scale corresponding to the aperture.

Macro lens depth of field (50mm F2.8 Macro, 100mm F2.8
Macro)
Refer to the depth-of-field table

 for details on depth of field.

• The depth-of-field scale and depth-of-field table

 is for 35mm-format

cameras. The depth-of-field is shallower when you use Digital Single Lens
Reflex Cameras equipped with an APS-C sized image sensor.

Macro photography

(50mm F2.8 Macro, 100mm

F2.8 Macro)

Magnification ratios

The magnification scale is located on the extending section of the lens barrel.
The line on the magnification scale which the edge of the outer lens barrel
overlaps indicates the current magnification ratio (1:1 in illustration

).

• As the magnification increases, the camera is more vulnerable to shaking. Use a

tripod to steady the camera when shooting.

Exposure Compensation (when using a hand-held
exposure meter, etc.)

As the magnification increases, the amount of light reaching the image sensor
decreases. This is automatically compensated in all autoexposure modes, or
in the manual exposure mode as long as the exposure is adjusted according to
the camera’s meter index. If your camera is set to the manual exposure mode
and you are using a hand-held exposure meter, or if your camera is set to the
manual exposure mode and you are using the Manual Flash Control function
available on some external flash units, refer to the exposure compensation
table

, and adjust exposure accordingly.

Exposure compensation table

a Exposure correction
b Magnification ratios
c Distance
(E.g., when adjusting by the aperture, +2 means opening the aperture 2 more
stops.)



1

2


KK-CA

1

2

3

4

5

6

7

*

8

*

50mm F2.8 Macro, 100mm F2.8 Macro

 

1

(1) (2) 2

(2)

2

 

*

50mm F2.8 Macro

100mm F2.8 Macro:

35mm F1.4 G:

50mm F2.8 Macro:

100mm F2.8 Macro:

(1)

(2)

(3)

Specifications

Name

(Model name)

Equivalent

35mm-format
focal length*

1

(mm)

Lens

groups-

elements

Angle of
view 1*

2

Angle of
view 2*

2

Minimum

focus*

3

(m (feet))

Maximum

magnification

(X)

Minimum

f-stop

Filter

diameter

(mm)

Dimensions

(maximum

diameter × height)

(mm (in.))

Mass

(g (oz.))

50mm F2.8 Macro

(SAL50M28)

75

6-7

47˚

32˚

0.2

(0.65)

1

f/32

55

Approx. 71.5Ч60

(2 13/16Ч2 3/8)

Approx. 295

(10 3/8)

100mm F2.8 Macro

(SAL100M28)

150

8-8

24˚

16˚

0.35
(1.2)

1

f/32

55

Approx. 75Ч98.5

(3Ч4)

Approx. 505

(18)

35mm F1.4 G
(SAL35F14G)

52.5

8-10

63˚

44˚

0.3
(1)

0.2

f/22

55

Approx. 69Ч76

(2 3/4Ч3)

Approx. 510

(18)

*

1

The value for equivalent 35mm-format focal length is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor.

*

2

The value of angle of view 1 is based on 35mm-format cameras, and that of angle of view 2 is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized

image sensor.

*

3

Minimum focus is the shortest distance from the image sensor to the subject.

• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.
• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused at infinity.

Included items: Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood

*

1

(1), Carrying case

*

2

(1), Set of printed documentation

*

1

The 50mm F2.8 Macro does not include a lens hood.

*

2

The 50mm F2.8 Macro and 100mm F2.8 Macro do not include a carrying case.

Designs and specifications are subject to change without notice.

is a trademark of Sony Corporation.

50mm F2.8 Macro:

m

F

2.8

4

5.6

8

11

16

22

32


28.0


20.1


14.3


10.1


7.16


5.08


3.61


2.57

2

2.14
1.88

2.20
1.83

2.29
1.77

2.45
1.69

2.70
1.59

3.17
1.47

4.22
1.32

7.96
1.16

0.4

0.404
0.396

0.405
0.395

0.407
0.393

0.410
0.390

0.415
0.386

0.422
0.381

0.431
0.373

0.446
0.364

0.27

0.271
0.269

0.272
0.268

0.273
0.268

0.274
0.266

0.275
0.265

0.277
0.263

0.281
0.260

0.285
0.257

0.23

0.231
0.229

0.231
0.229

0.232
0.228

0.232
0.228

0.233
0.227

0.235
0.226

0.237
0.224

0.239
0.222

0.21

0.211
0.209

0.211
0.209

0.211
0.209

0.212
0.208

0.212
0.208

0.213
0.207

0.215
0.205

0.217
0.204

0.203

0.204
0.202

0.204
0.202

0.204
0.202

0.205
0.202

0.205
0.201

0.206
0.200

0.207
0.199

0.209
0.198

0.200

0.201
0.200

0.201
0.200

0.201
0.200

0.201
0.200

0.201
0.200

0.201
0.199

0.202
0.199

0.202
0.198

100mm F2.8 Macro:

m

F

2.8

4

5.6

8

11

16

22

32


107


75.8


53.6


38.0


26.9


19.0


13.5


9.55

3

3.07
2.93

3.11
2.90

3.16
2.86

3.23
2.80

3.33
2.73

3.50
2.63

3.76
2.50

4.21
2.34

1

1.00
0.993

1.00
0.991

1.01
0.987

1.01
0.982

1.02
0.975

1.03
0.965

1.05
0.951

1.08
0.932

0.6

0.602
0.598

0.602
0.598

0.603
0.597

0.605
0.595

0.607
0.593

0.610
0.593

0.614
0.587

0.619
0.582

0.45

0.451
0.449

0.451
0.449

0.451
0.449

0.452
0.448

0.452
0.448

0.453
0.447

0.455
0.445

0.457
0.443

0.4

0.400
0.400

0.400
0.400

0.401
0.399

0.401
0.399

0.401
0.399

0.402
0.398

0.403
0.397

0.404
0.396

0.37

0.370
0.370

0.370
0.370

0.370
0.370

0.370
0.370

0.371
0.369

0.371
0.369

0.371
0.369

0.372
0.368

0.352

0.352
0.352

0.352
0.352

0.352
0.352

0.352
0.352

0.352
0.352

0.352
0.351

0.353
0.351

0.353
0.351

50mm F2.8 Macro:

a

+2

1.00X

(1:1)

0.89X

(1:1.13)

0.74X

(1:1.36)

0.59X

(1:1.68)

0.47X

(1:2.15)

0.35X

(1:2.9)

0.24X

(1:4.2)

0.14X

(1:7.2)

0.04X

(1:22.6)

0.200

0.202

0.207

0.217

0.235

0.267

0.329

0.482

1.27

m

+1

+1

3

/

4

+

3

/

4

+

1

/

2

+

1

/

4

+1

1

/

2

+1

1

/

4

0

b

c

100mm F2.8 Macro:

a

+2

1.00X

(1:1)

0.93X

(1:1.08)

0.81X

(1:1.23)

0.64X

(1:1.56)

0.49X

(1:2.04)

0.36X

(1:2.78)

0.19X

(1:5.26)

0.077X

(1:12.99)

0.025X

(1:40)

0.352

0.355

0.363

0.385

0.420

0.481

0.678

1.47

4.06

m

+1

+1

3

/

4

+

3

/

4

+

1

/

2

+

1

/

4

+1

1

/

2

+1

1

/

4

0

b

c

–(2)

–(3) 50mm F2.8

Macro, 100mm F2.8 Macro

LIMIT

50mm F2.8 Macro

20cm

27cm

30cm

100mm F2.8 Macro

35cm

54cm

59cm

LIMIT

LIMIT

FULL

FULL

50mm F2.8 Macro, 100mm

F2.8 Macro

35mm

APS-C

50mm F2.8 Macro,

100mm F2.8 Macro

1:1

a

b

c

2

2

1

....................... 0570-00-0770

(

PHS

.....0466-38-0231

(

)

9

8

9

5

–2

35mm

*

1

(mm)

1*

2

2*

2

*

3

(m)

(mm)

(mm)

(g)

50mm F2.8 Macro

(SAL50M28)

75

6-7

47

32

0.2

1

F32

55

71.5 60

295

100mm F2.8 Macro

(SAL100M28)

150

8-8

24

16

0.35

1

F32

55

75 98.5

505

35mm F1.4 G
(SAL35F14G)

52.5

8-10

63

44

0.3

0.2

F22

55

69 76

510

*

1

35mm

APS-C

*

2

1 35mm

2 APS-C

*

3

ADI

ADI

(1)

(1)

(1)

*

1

(1)

*

2

(1)

*

1

50mm F2.8 Macro

*

2

50mm F2.8 Macro, 100mm F2.8 Macro

2-685-162-

03(1)

/Lens for

Digital Single Lens Reflex Camera/

Objectif pour appareil photo numérique

reflex à objectifs interchangeables

/Operating Instructions/Mode d'emploi/

Manual de instrucciones

50mm F2.8 Macro

100mm F2.8 Macro

35mm F1.4 G

©2006 Sony Corporation Printed in Japan

SAL50M28/100M28/35F14G

100mm F2.8 Macro

(50mm F2.8 Macro)

35mm F1.4 G:

100mm F2.8 Macro:

35mm F1.4 G:

This manual is related to the following products:
Table of contents