Metrohm 726 Titroprocessor User Manual

Page 78

5.2 Method editor

726 Titroprocessor, Instructions for use

In order to define the command sequence enter the required command in

the command column manually (the first letters are sufficient) or select a

command from the nested selection list.

³ t/s Command Parameters

³ ДДДДД ДДДДДДДДДДДДД ДДДДДДДДДДДДДДДДДДДДДДДД

³ 1

³ 2 END ЪДДДДДДДДДДД¿

³ ³

Titration >

³ ³Changer ЪДДДДДДД¿

³ ³CAL ³

DET_* >

³ ³MEAS_* ³MET_* ЪДДДДДДДДД¿

³ ³DOS ³SET_* ³

DET_PH*

³ ³STIR_I ³SEC_* ³DET_U* ³

³ ³CASE ³KFT_* ³DET_UPOL*³

³ ³COMM ³KFC_* ³DET_IPOL*³

³ ³AUX АДДДДДДБДДДДДДДДДЩ

³ АДДДДДДДДДДДЩ

When the command has been accepted with the parameters of

the selected command are shown and can now be edited. The titration and

measuring modes (all *commands) have extended sets of parameters.

These can be accessed via the [* ...] softkeys. If a command marked
with an asterisk is marked with the cursor in the command column then the
[* Param] [*Formula] [*Report]

softkeys are activated. In this way

the further settings which only apply to this particular command or mode

can be edited.

ЪДДД Method : HCl.mth ДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДД¿

³ ³

³ t/s Command Parameters Parameters ³

³ ДДДДД ДДДДДДДДДДДДД ДДДДДДДДДДДДДДДДДДДДДДДД ДДДДДДДДДДДДДДДДДДДДДДДД ³

³ 1! MEAS_PH* pH measurement ³

³ Sensor 6.0232.100 Signal drift 50 mV/min ³

³ Meas. input A1 Equilibr.time auto s ³

³ Temperature 25.0 øC ³

³ 2 180 DET_PH* Dynamic equivalence point titration ³

³ Reagent HCl Sensor 6.0232.100 ³

³ Concentr. 0.1 mol/L Meas. input A1 ³

³ Dos. drive A1 ³

³ 3 END ³

³ ³

АДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДД Quit ДЩ

ЪДДДДДДДВДДДДДДДВДДДДДДД¿ ЪДДДДДДДВДДДДДДДВДДДДДДД¿ ЪДДДДДДДВДДДДДДДВДДДДДДД¿

³ Note ³ File ³Determ.³ ³ * ³ * ³ * ³ ³Insert ³Delete ³ >> ³

³ ³ ³report ³ ³ Param ³Formula³ Report³ ³line ³line ³ >> ³

АДДДДДДДБДДДДДДДБДДДДДДДЩ АДДДДДДДБДДДДДДДБДДДДДДДЩ АДДДДДДДБДДДДДДДБДДДДДДДЩ

A command line consists of a line number with the line attribute, the line

time, a command name and the parameters.

With a ’!’ sign as line attribute the execution of a line can be suppressed (if
required); see line 1 above. A block of lines to be suppressed can be

marked with an ‘@’ sign in the first and last lines. This possibility can be very
useful when a newly created method is being tested.

A line time (see line 2 above) can be entered as an option; this sets a

minimum time in which a command must be carried out. The next

Allocation parameters

Mode-specific settings

Measuring

mode

Titration

mode