Brocade FastIron Ethernet Switch Layer 3 Routing Configuration Guide - Manual (Page 366)

Current Route count: 309
Intra: 304 Inter: 4 External: 1 (Type1 0/Type2 1)
Equal-cost multi-path: 56
OSPF Type: IA- Intra, OA - Inter, E1 - External Type1, E2 - External Type2
Destination Cost E2Cost Tag Flags Dis
E2 ::/0 2 1 0 00000003 110
Next_Hop_Router Outgoing_Interface Adv_Router
fe80::768e:f8ff:fe3e:1800 e 4/3/1 192.168.98.111
fe80::768e:f8ff:fe3e:1800 ve 17 192.168.98.111
Destination Cost E2Cost Tag Flags Dis
IA 5100::192:61:1001:0/112 3 0 0 00000007 110
Next_Hop_Router Outgoing_Interface Adv_Router
fe80::768e:f8ff:fe3e:1800 e 4/3/1 192.168.98.111
fe80::768e:f8ff:fe3e:1800 ve 17 192.168.98.111
Destination Cost E2Cost Tag Flags Dis
IA 5100::192:111:2:111/128 1 0 0 00000007 110
Next_Hop_Router Outgoing_Interface Adv_Router
fe80::768e:f8ff:fe3e:1800 e 4/3/1 192.168.98.111
fe80::768e:f8ff:fe3e:1800 ve 17 192.168.98.111
Destination Cost E2Cost Tag Flags Dis
IA 5100::192:111:3:111/128 1 0 0 00000007 110
Next_Hop_Router Outgoing_Interface Adv_Router
fe80::768e:f8ff:fe3e:1800 e 4/3/1 192.168.98.111
--More--, next page: Space, next line: Return key, quit: Control-c
Syntax: show ipv6 ospf routes [ipv6-prefix]
The ipv6-prefix parameter specifies a destination IPv6 prefix. (You do not need to specify the length of
the prefix.) If you use this parameter, only the route entries for this destination are shown.
For example, to display route information for the destination prefix 2000::, enter the following
command at any level of the CLI.
device# show ipv6 ospf routes 5100::192:111:42:111
Destination Cost E2Cost Tag Flags Dis
IA 5100::192:111:42:111/128 1 0 0 00000007 110
Next_Hop_Router Outgoing_Interface Adv_Router
fe80::768e:f8ff:fe3e:1800 e 4/3/1 192.168.98.111
fe80::768e:f8ff:fe3e:1800 ve 17 192.168.98.111
OSPFv3 route information TABLE 81
This field Displays
Current Route Count (Displays
with the entire OSPFv3 route
table only) The number of route entries currently in the OSPFv3 route table.
Intra/Inter/External (Type1/
Type2) (Displays with the entire
OSPFv3 route table only) The breakdown of the current route entries into the following route types:
• Inter - The number of routes that pass into another area.
• Intra - The number of routes that are within the local area.
• External1 - The number of type 1 external routes.
• External2 - The number of type 2 external routes.
Equal-cost multi-path (Displays
with the entire OSPFv3 route
table only) The number of equal-cost routes to the same destination in the OSPFv3 route
table. If load sharing is enabled, the device equally distributes traffic among
the routes.
Destination The IPv6 prefixes of destination networks to which the device can forward
IPv6 packets. "*IA" indicates the next router is an intra-area router.
Cost The type 1 cost of this route.
OSPFv3
366 FastIron Ethernet Switch Layer 3 Routing Configuration Guide
53-1003087-04