Rockwell Automation 1336E IMPACT Adjustable Frequency AC Drive User Manual V 1-4.XX - Manual (Page 89)

Using the L Option 5-7
Figure 5.2
L Option Mode Selection and Typical TB3 Connections
1 See Speed Select table.
2 Drive must be stopped to take Local Control. Control by all other adapters is disabled (except Stop).
3 These inputs must be present before drive will start.
4 For Common Bus, this becomes Precharge Enable.
5 Bit 11 of Logic Options (parameter 17) must be 0 for reverse direction control.
6 For soft faults only. You need to recycle power to the drive to clear. For hard faults, refer to the Troubleshooting chapter.
7 To configure the stop type, refer to Logic Options (parameter 17).
8 This input must be present before the fault can be cleared and the drive will start. This can be disabled through Fault Select 2 (parameter 22)
and Warning Select 2 (parameter 23).
9 Latched starts require a stop to stop the drive. Note: This only affects the L Option stop. For modes that do not have Stop Type, stop commands
follow Stop 1 in Logic Options.
10 See Speed/Torque Select table. This takes precedence over Spd/Trq Mode Sel (parameter 68).
11 Unlatched (maintained) start.
12 In modes 5, 9, 10, and 15, the MOP value is not reset to 0 when you stop. In modes 27, 28, 29, and 30, the MOP value is reset to 0 when you stop.
NOTE: For detailed information on Modes 31 and 32 which were added for Speed Profiling applications, refer to page 9-23 in this manual.
19
20
21
22
23
24
25
26
27
28
29
30
Start
Not Stop , Clear Fault
Common
Not Ext Fault
Common
Speed Select 1
Common
Enable
Forward Forward Digital
Pot Dn
Forward 2nd
Accel
Jog Speed
Select 3
Speed
Select 3
Digital
Pot Up
1st
Decel
Reverse Reverse Digital
Pot Up
Reverse 1st
Accel
7 8 9 10 11
Mode
Speed
Select 2
Speed
Select 2
Speed
Select 2
Digital
Pot Dn
2nd
Decel
Speed/
Torque 2
Speed/
Torque 2
Forward Speed/
Torque 2
Speed/
Torque 1
Speed/
Torque 1
Ramp
Disable
Speed/
Torque 1
Speed/
Torque 3
Speed/
Torque 3
Reverse Speed/
Torque 3
19 20 21 22
Process
Trim
Flux
Enable
Reset Speed
Select 2
Digital
Pot Dn
Forward
Speed
Select 3
Digital
Pot Up
Digital
Pot Up
Reverse
28 29
Speed
Select 2
Digital
Pot Dn
THREE WIRE
Run Forward
Not Stop , Clear Fault
Common
Run Reverse
Not Ext Fault
Common
Speed Select 2
Speed Select 1
Common
Enable
Local
Control
Stop
Type
2nd/1st
Accel
Digital
Pot Up
Local
Control
Speed
Select 3
Speed
Select 3
2nd/1st
Decel
Digital
Pot Dn
Stop
Type
12 13 14 15 16
Mode
19
20
21
22
23
24
25
26
27
28
29
30
Process
Trim
Flux
Enable
Process
Trim
Reset Reset Ramp
Disable
23 24 25
Jog
Speed
Select 3
26
Digital
Pot Up
Digital
Pot Dn
30 31 & 32
See Note Below
TWO WIRE
1
2
3
4
5
7
9
12
10
3
5
5
5
5
5
5
5
5
5
12 12 12
10
10
10
10
1 1
1 1
1 1
1
1
5,
3, 6 7
5, 11
4, 8
1
1
1
3
1 1
2 7
12
11
6
8
10
10
10
10
,
,