Lenze EVS9332xK - Manual (Page 381)

Appendix
5.2 Index
5−7
l
EDSVS9332K−EXT EN 4.0
− digital frequency input (DFIN), 3−141
− Digital frequency output (DFOUT), 3−144
− Digital frequency processing (DFSET), 3−154
− digital frequency ramp function generator (DFRFG), 3−148
− Digital frequency switch (SWPHD), 3−304
− Digital inputs (DIGIN), 3−161
− Digital outputs (DIGOUT), 3−162
− Digital status signals (STAT), 3−292
− Display code, 3−7
− drive control (DCTRL)
controller inhibit (CINH), 3−139
operation inhibit (DISABLE), 3−138
quick stop (QSP), 3−138
TRIP reset, 3−139
TRIP set, 3−139
− drive control (DCTRLC), 3−137
− Edge evaluation (TRANS), 3−314
− Establish connections, 3−10
− Extrapolation (EXTPOL1), 3−164
− extrapolation (EXTPOL2), 3−167
− Fixed setpoints (FIXSET), 3−179
− Flipflop (FLIP), 3−181
− Flipflop element (FLIPT), 3−184
− following error monitoring (CERR), 3−82
− free codes (FCODE) of the measuring systems, 3−171
− Free digital outputs (FDO), 3−172
− Free piece counter (FCNT), 3−170
− gearbox compensation (GEARCOMP), 3−186
− holding brake (BRK), 3−61
− holding brake (BRK1)
disengaging the brake, 3−63
engaging the brake, 3−63
setting controller inhibit, 3−64
− homing function (REFC), 3−261
− Input name, 3−6
− Input symbol, 3−6
− Internal motor control (MCTRL), 3−190
− Inverter (ANEG), 3−52
− Limiting element (LIM), 3−187
− limiting element (LIMPHD1), 3−188
− Logic NOT, 3−218
− mains failure detection (MFAIL), 3−199
− master selection (MSEL), 3−215
− Monitor outputs of monitoring system (MONIT), 3−211
− Motor phase failure detection (MLP), 3−210
− Motor potentiometer (MPOT), 3−212
− multi−axis synchronisation (SYNC), 3−305
− Naming, 3−6
− OR operation (OR), 3−226
− Oscilloscope function (OSZ), 3−230
− Output name, 3−7
− Output symbol, 3−7
− overview, 3−14
− Parameter setting code, 3−7
− phase integrator (PHINT5), 3−249
− Position memory (PSAVE), 3−255
− Position signals, Transfer of several signals at the same time,
3−118
− position switch points (SPC), 3−284
− Positioning control (VTPOSC), 3−321
− Process controller (PCTRL1), Dancer position, tension, pressure
controller, 3−234
− ramp function generator for angle signals (RFGPH), 3−270
− ramp function generator for angle signals (RFGPH2/3), 3−275
− Ramp generator(RFG), 3−268
− Remove connections, 3−11
− Sample and hold function (S&H), 3−281
− setpoint conditioning (CCTRL), 3−67
− setpoint conditioning (CCTRL2), 3−74
− shift register (STORE3), 3−298
− Signal conversion (CONV), 3−108
− Signal types, 3−5
− Speed setpoint conditioning (NSET), 3−220
− State bus connection, 3−293
− storage block (STORE1), 3−294
− storage block (STORE2), 3−297
− Stretching, compression, offset in Y direction (YSET1), 3−330
− system bus (CAN−IN), 3−66
− system bus (CAN−OUT), 3−66
− virtual clutch (CLUTCH1), 3−85
− virtual clutch (CLUTCH2), 3−89
− virtual master (VMAS), 3−317
− welding bar control (WELD1), 3−323
Function blocks , Freely assignable input
variables (FEVAN), 3−174
function blocks, S−shaped ramp function
generator (SRFG), 3−290
Function library, 3−1
G
Gearbox compensation (GEARCOMP), 3−186
Global Drive Control, configuration with, 2−3
H
Holding brake (BRK), 3−61
Homing
− CCTRL function block, 3−69
− CCTRL2 function block, 3−77
− REFC function block, 3−262
Homing function (REFC), 3−261
− profile generator, 3−262
− reference run modes, 3−263