Configuring spoke 2 – H3C Technologies H3C SecPath F1000-E User Manual
Page 443
431
d.
Enter the area ID 0. Select Normal as the area type. Enter the network address 10.0.3.0, select
the network mask 0.0.0.255, and then click Add Network. Enter the network address 10.0.1.0,
select the network mask 0.0.0.255, and then click Add Network. Click Apply.
e.
Click More>> to perform OSPF interface configuration.
f.
Click the
icon of interface Tunnel1.
g.
Enter 10 as the Hello interval. Enter 40 as the Dead interval. Select Broadcast as the network
type. Select 0 as the DR priority. Click Apply.
Configuring Spoke 2
The Spoke 2 configuration page is similar to the Hub 1 configuration page. See the figures for Hub 1
configuration.
1.
Configure IP addresses for the interfaces. (Details not shown)
2.
Configure tunnel interface Tunnel1 for VPN domain vpn1:
a.
From the navigation tree, select VPN > DVPN > Client, and then click Add.
b.
Select the tunnel encapsulation mode UDP. Enter the tunnel interface number 1. Enter the IP
address/mask 10.0.1.4/24. Select security zone Management for the tunnel interface. Select
the tunnel source interface GigabitEthernet0/1. Enter the VPN domain name vpn1. Enter the
VAM server address 192.168.1.22. Enter the backup VAM server address 192.168.1.33.
Enter the VAM client username dvpn1spoke2. Enter the VAM client password dvpn1spoke2.
Enter the VAM client pre-shared key 123.
c.
Select Enable IPsec.
d.
Select the IPsec authentication method Pre-Shared Key and then enter abcde in the field.
e.
Select IP Address as both the remote ID type and the local ID type.
f.
Click Apply.
3.
Configure tunnel interface Tunnel2 for VPN domain vpn2:
a.
From the navigation tree, select VPN > DVPN > Client, and then click Add.
b.
Select tunnel encapsulation mode GRE. Enter tunnel interface number 2. Enter IP address/mask
10.0.2.4/24. Select security zone Management for the tunnel interface. Select tunnel source
interface GigabitEthernet0/1. Enter VPN domain name vpn2. Enter the VAM server address
192.168.1.22. Enter the backup VAM server address 192.168.1.33. Enter the VAM client
username dvpn2spoke2. Enter the VAM client password dvpn2spoke2. Enter the VAM client
pre-shared key 456.
c.
Select Enable IPsec.
d.
Select the IPsec authentication method Pre-Shared Key and then enter abcde in the field.
e.
Select IP Address as both the remote ID type and the local ID type.
f.
Click Apply.
4.
Configure OSPF:
a.
From the navigation tree, select Network > Routing Management > OSPF.
b.
Select Enable OSPF and click Apply.
c.
In the Area Configuration area, click Add.
d.
Enter the area ID 0. Select Normal as the area type. Enter the network address 10.1.4.0, select
the network mask 0.0.0.255, and then click Add Network. Enter the network address 10.0.1.0,
select the network mask 0.0.0.255, and then click Add Network. Click Apply.
e.
Click More>> to perform OSPF interface configuration.
- H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS