Brocade Fabric OS Message Reference (Supporting Fabric OS v7.3.0) - Manual (Page 379)

Fabric OS Message Reference 357
53-1003140-01
FABS-1005
5
FABS-1005
Message
(= ).
Message Type
LOG
Severity
WARNING
Probable Cause
Indicates that an unsupported operation has been requested. This is usually an internal Fabric OS
problem or file corruption. The following is a possible value for function name and description of problem
variable:
fabsys_write: Unsupported write operation: process xxx
In this value, xxx is the process ID (PID), which could be any whole number.
Recommended
Action
Reboot or power cycle the active CP (for modular systems) or the switch (for single-board systems).
If the message persists, run the firmwareDownload command to update the firmware.
FABS-1006
Message
: object unit .Message TypeLOGSeverityWARNINGProbable CauseIndicates that there is no device in the slot with the specified object type ID in the system module record.
This could indicate a serious Fabric OS data problem on the switch. The possible values for function
name and description of problem variable are:•setSoftState: bad object•setSoftState: invalid type or unit•media_sync: Media oid mapping failed•fabsys_media_i2c_op: Media oid mapping failed•fabsys_media_i2c_op: obj is not media type•media_class_hndlr: failed sending media state to blade driver RecommendedActionIf the message is isolated, monitor the error messages on the switch. If the error is repetitive or if the
fabric failed, failover or reboot the switch.If the message persists, run the firmwareDownload command to update the firmware. Pages: 1 … 377 378 379 380 381 … 1008 wrong Brand wrong Model non readable See also other documents in the category Brocade Computer Accessories: ICX 6650 Hardware Installation Guide (98 pages) FastIron Ethernet Switch Administration Guide (362 pages) FastIron Ethernet Switch Feature and RFC Support Matrix (66 pages) FastIron Ethernet Switch Traffic Management Guide (100 pages) FastIron Ethernet Switch Stacking Configuration Guide (160 pages) FastIron Ethernet Switch Software Upgrade Guide (121 pages) FastIron Ethernet Switch Software Licensing Guide (58 pages) FastIron Ethernet Switch Security Configuration Guide (396 pages) FastIron Ethernet Switch Platform and Layer 2 Switching Configuration Guide (454 pages) FastIron Ethernet Switch Layer 3 Routing Configuration Guide (672 pages) FastIron Ethernet Switch IP Multicast Configuration Guide (230 pages) FastIron SX, FCX, and ICX Diagnostic Reference (222 pages) ICX 7750 Hardware Installation Guide (80 pages) Network OS YANG Reference Manual v4.1.1 (238 pages) Network OS Software Licensing Guide v4.1.0 (34 pages) Network OS NETCONF Operations Guide v4.1.1 (622 pages) Network OS Message Reference v4.1.1 (478 pages) Network OS Feature and RFC Support Matrix (16 pages) Network OS Command Reference v4.1.0 (1418 pages) Network OS Administrator’s Guide v4.1.1 (748 pages) Mid-Mount Rack Kit (Switch) Installation Procedure (Supporting 300, 5100, 5300, 6505, 6510, 6520, 7800, 8000, VA-40FC, VDX 6710-54, and VDX 6740) (10 pages) Flush Mount Rack Kit Installation Procedure (Supporting VDX 6710-54, VDX 6720-24, VDX 6720-60, VDX 6730-32, VDX 6730-76, and VDX 6740) (10 pages) VDX 6710-54 QuickStart Guide (12 pages) VDX 6710-54 Hardware Reference Manual (72 pages) VDX 6730 Hardware Reference Manual (Supporting VDX 6730-32 and VDX 6730-76) (90 pages) VDX 6730 QuickStart Guide (Supporting VDX 6730-32 and VDX 6730-76) (12 pages) Fixed Rack Mount Kit Installation Procedure (Supporting 300, 5100, 5300, 6520, 7800, 8000) (12 pages) VDX 8770-8 Two-Post Flush and Mid-Mount Rack Kit Installation Procedure (8 pages) VDX 8770-8 QuickStart Guide (34 pages) VDX 8770-8 Hardware Reference Manual (136 pages) VDX 8770-8 Four-Post Flush and Recessed Mount Rack Kit Installation Procedure (10 pages) VDX 8770-4 Two-Post Flush and Mid-Mount Rack Kit Installation Procedure (10 pages) VDX 8770-4 QuickStart Guide (32 pages) VDX 8770-4 Hardware Reference Manual (132 pages) VDX 8770-4 Four-Post Flush Mount Rack Kit Installation Procedure (8 pages) VDX 8770-4 Four-Post Flush and Recessed Mount Intake Air Duct Rack Kit Installation Procedure (24 pages) VDX 6740 Hardware Reference Manual (Supporting VDX 6740, VDX 6740T, and VDX 6740T-1G) (78 pages) Universal Four Post Rack Kit Installation Procedure (Supporting VDX 6740T) (20 pages) Universal Two-Post Rack Kit Installation Procedure (Supporting VDX 6740T) (12 pages) FCX Series Hardware Installation Guide (112 pages) 6910 Ethernet Access Switch MIB Reference (102 pages) 6910 Ethernet Access Switch Hardware Installation Guide (84 pages) 6910 Ethernet Access Switch Diagnostic Guide (Supporting R2.2.0.0) (88 pages) 6910 Ethernet Access Switch Configuration Guide (Supporting R2.2.0.0) (1240 pages) Unified IP MIB Reference (Supporting Multi-Service IronWare Release 05.6.00a) (771 pages) Sitemap
Message Type
LOG
Severity
WARNING
Probable Cause
Indicates that there is no device in the slot with the specified object type ID in the system module record.
This could indicate a serious Fabric OS data problem on the switch. The possible values for function
name and description of problem variable are:
• setSoftState: bad object
• setSoftState: invalid type or unit
• media_sync: Media oid mapping failed
• fabsys_media_i2c_op: Media oid mapping failed
• fabsys_media_i2c_op: obj is not media type
• media_class_hndlr: failed sending media state to blade driver
Recommended
Action
If the message is isolated, monitor the error messages on the switch. If the error is repetitive or if the
fabric failed, failover or reboot the switch.
If the message persists, run the firmwareDownload command to update the firmware.