Daktronics OmniSport 2000 Timing Console - Manual (Page 276)

224 Menu Navigation Shortcuts
2-6) NETWORK configures the ETHERNET port
2-6-1) NETWORK ENABLE enables/disables the ETHERNET port (ON or OFF)
2-6-2) IP ADDRESS sets the IP Address
2-6-3) SUBNET MASK sets the Subnet Mask
2-6-4) GATEWAY ADDRES sets the Gateway Address
2-6-5) RTD PORT # sets the Real-Time Data port number
2-6-6) MAC ADDRESS
displays the console’s MAC Address
2-6-7) NETWK PRO/MMR enables/disables Pro Software (ON or OFF)
3) TEST MENU
3-1) BATTERY checks battery power level
3-2) SCOREBOARD allows testing of the scoreboard
3-2-1) CYCLE ON/OFF sends an all ON signal to the scoreboard in 3 second intervals
3-2-2) DRIVER ADDRESS displays the driver address(es)
3-2-3) DIGIT NUMBER displays digit numbers
3-3) JUDGE CONSOLES indicates proper connection of judge consoles
3-4) CAN NETWORK allows advanced debugging (Daktronics service personnel only)
6-Track Menu Navigation
1) SCBD MENU
1-1) SCBD ON/OFF clears the display
1-2) DIMMING sets the dimming (brightness) level of the display
1-3) TIME OF DAY displays the Time-of-Day and time format
2) EDIT MENU
2-1) TEAM SCORE allows editing of team scores
2-2) RECORD TIME allows editing of record times
3) PRINT MENU
3-1) RACE RESULTS prints the results of a specific race or a complete meet
3-2) SETTINGS prints out all configurations entered in the Setup Menu
4) SETUP MENU
4-1) TIMER configures the timer settings
4-1-1) # OF LANES sets the number of lanes
4-1-2) START IN sets the type of start input (Normally Open or Normally Closed)
4-1-3) PRIMARY TIME sets the number of buttons used per lane (J7 1BTN or J10 3 BTN)
4-1-4) PRECISION sets the timer precision in seconds (1/100 or 1/1000)
4-1-5) BEEPER VOLUME sets the volume of the internal beeper
4-2) SCOREBOARD configures the scoreboard settings
4-2-1) NUMERIC sets output data for numeric scoreboards
4-2-1-1) # OF LINES sets the number of lines on the scoreboard
4-2-1-2) FIN PAGE TIME sets the hold time for finish pages
4-2-1-3) RESULTS ORDER sets order of results (LANE or PLACE)
4-2-1-4) SHOW DQ sets what DQ data to display (DQ ONLY or DQ/TIME)
4-2-1-5) FOOTBALL SCBD sets what data to display (EVENT/HEAT or GUEST 2/3)
4-2-1-6) RUNNING TIME sets what data to display (CONTINUOUS or FINISH)
4-2-2) RTD/MATRIX sets output data for matrix displays
4-2-2-1) # OF LINES sets the number of lines on the display
4-2-2-2) FIN PAGE TIME sets the hold time for finish pages
4-2-2-3) RESULTS ORDER sets order of results (LANE or PLACE)
4-2-2-4) SHOW DQ sets what DQ data to display (DQ ONLY or DQ/TIME)
4-2-2-5) RTD OFFSET sets how data is sent to the display with 2+ consoles or pools
4-3) COMM PORTS configures the communication ports
4-3-1) SCBD OUTPUTS sets the J2/J3 protocol (MULTIDROP, MULTILINE, or OMEGA)
4-3-2) RTD PORT sets the J5 protocol (RTD or CTS)
4-3-3) RESULTS PORT sets the J6 protocol (OMNI 2000, OMNI 6000, or CTS)