MagTek EC2000 99875607 User Manual
Expresscard 2000
Table of contents
Document Outline
- Table of Contents
- 1 Required Tools, Materials, and Documents
- 2 Introduction
- 2.1 Recommended Preparation for Service Appointments
- 2.2 Important Safety Information
- 2.3 How to Handle ESD-Sensitive Parts
- 2.4 Introduction to EC2000 Components
- 2.5 Device Specifications
- 2.6 About Installation & Operation
- 2.7 How to Open the Top Access Door
- 2.8 How to Safely Move Transports By Hand
- 2.9 How to Use Maintenance Functions On the Touchscreen
- 3 Preventive Maintenance
- 3.1 Prepare the Device for Preventive Maintenance
- 3.2 Clean the Card Path
- 3.3 Clean All Transport Rollers
- 3.4 Update the Software
- 3.5 Update the Firmware
- 3.6 Service the Hopper Module
- 3.7 Service the XY Transport Module
- 3.8 Service the Exit Transport Module
- 3.9 Cool the Tipper Heater / Power Down the Device
- 3.10 Clean Inside the Device
- 3.11 Service the Image Printer Module
- 3.12 Service the Embosser Module
- 3.13 Service the Electronics
- 3.14 Service the Cover
- 3.15 Perform Final Tests
- 4 Removal and Re-installation
- 4.1 How to Prepare the Device for Removing / Re-installing Modules
- 4.2 How to Remove / Re-install the Top Access Door
- 4.3 How to Remove / Re-install the Side Access Doors
- 4.4 How to Remove / Re-install the Cover
- 4.5 How to Remove / Re-install the Hopper Module
- 4.6 How to Remove / Re-install the Image Print Head
- 4.7 How to Remove / Re-install the Image Printer Module
- 4.8 How to Remove / Re-install the XY Transport Ribbon Cable
- 4.9 How to Remove / Re-install the XY Transport Module
- 4.10 How to Remove / Re-install Embosser Fonts
- 4.11 How to Remove / Re-install the Embosser Module
- 4.12 How to Remove / Re-install the Tipper Heater
- 4.13 How to Remove / Re-install the Tipper and Exit Ramp Module
- 4.14 How to Remove / Re-install the Exit Transport Module
- 4.15 How to Remove / Re-install the Embedded PC
- 4.16 How to Remove / Re-install the Embedded PC Solid State Drive (SSD)
- 4.17 How to Remove / Re-install the Main Logic Board (MLB)
- 4.18 How to Remove / Re-install the Power Controller and Backplane
- 4.19 How to Remove / Re-install the Power Supply
- 4.20 How to Remove / Re-install the Magnetic Stripe Reader (MSR) Module
- 4.21 How to Remove / Re-install the Touchscreen
- 5 Adjustments
- 5.1 How to Calibrate the Touchscreen
- 5.2 How to Calibrate the Hopper Transport Module
- 5.3 How to Calibrate the XY Transport Module
- 5.4 How to Calibrate the Embosser Module
- 5.4.1 About Embosser Calibration
- 5.4.2 How to Calibrate the Embosser Wheel Home Position
- 5.4.3 How to Measure Embossed Character Thickness
- 5.4.4 How to Pre-Set Embosser Defaults
- 5.4.5 How to Set Minimum Thickness Using CamAngle
- 5.4.6 How to Calibrate Card Flatness
- 5.4.7 How to Fine-Tune Embossed Character Height Using Software
- 5.4.8 Aligning Embossed Characters with Printed Characters
- 5.5 How to Calibrate the Indenter Module
- 5.6 How to Calibrate the Image Printer Module
- 5.7 How to Minimize Image Printer Margins
- 5.8 How to Calibrate the Tipper Module
- 6 Diagnosis