IAI America SSEL - Manual (Page 479)

457
Appendix
(In the panel
wind
ow, the three di
gits after “E” in
dicate an error n
u
mber.)
Error No.
Error name
Description, ac
tion, etc.
E18
T
a
sk
ID error
T
he task ID is i
n
valid.
E19
WAIT
factor error
T
he WA
IT
factor is invalid.
E1A
WAIT
logic error
T
he WA
IT
logic is invali
d.
E1B
Point-data vali
d addr
ess error
Point-data valid addr
ess is not set.
E1C
Source data er
ror
T
he source dat
a is invalid.
E1D
Unaffected
out
put number err
or
T
he unaffected output num
ber
is invali
d. A value other than
an output port
number (“0” is acceptable) may
be input
in I/O parameter Nos. 70 to 73.
E1E
Zone par
ameter error
A value other than an outp
u
t port/global flag number (“0” is
acceptable) or
duplicate
numbers may
be input in ax
is-s
pecific parameter
Nos. 88, 91, 94 and
97, or the output number specified as s
y
stem output in the I/O parameter
for
output function selection may
be
duplic
ated,
among other reasons.
E1F
I/O assignment
parameter err
or
A value other than an I/O port number (“-1” is acceptable) or other than an I/O head port number + [multiple
of
8] may
be input in I/O parameter Nos. 2 to 9, or a
value other than a [multiple of 8] may
be
input in I/O parameter Nos. 14 to 17.
E20
I/O assignment
duplication err
or
I/O
assignment
s are duplicat
ed. Check I/O parameter Nos. 2 to 9 and 14 to 17
and the I/O slot card t
y
pe (number of I/Os),
etc.
E21
I/O assignment
count over err
or
T
he I/O assignments ex
ce
ed the spec
ified ra
nge. Check I/O parameter Nos. 2 to
9 and 14 to 17
and the I/O slot card t
y
pe (number of I/Os).
E22
Header error (
S
lave comm
unication)
T
he header i
n
t
he message received from the slave car
d is invalid.
E23
Card ID error (
S
lave comm
unication)
T
he card ID in
the message receiv
ed from the slav
e card i
s
invali
d.
E24
Response t
y
pe error (Slave c
o
mmunic
ation)
T
he response t
y
pe
in the mes
sage rec
eived from the slave c
a
rd is inv
ali
d.
E25
Command t
y
pe error (Slave c
o
mmunic
ation)
T
he command t
y
pe of the transmitting comm
and is i
n
val
id.
E26
T
a
rget ty
pe err
or
T
he target ty
pe is invalid.
E27
No target error
T
a
rget (dri
ver card, I/O card, e
n
coder or other
slave card) is
not installed.
E29
EEPROM error (EWEN/EWD
S not permitte
d)
EEPROM access error (
w
hen w
rit
ing)
E2A
Read compar
e mismatch error during EEPROM
w
rite
EEPROM access error (
w
hen w
rit
ing)
E2B
Abnorm
al response err
or
w
h
en sending EEPROM informati
on
acquisition command
An abnormal r
e
sponse
w
a
s receiv
ed
w
h
en
a slave-EEP
R
O
M information
acquisition command
w
a
s sent.
E2C
Maximum receive size over
er
ror
w
hen sending EEPROM
informati
on ac
quisiti
on comm
and
T
he maximum
receiv
e size exceeds the l
imit value
w
h
en a s
lave-EEP
ROM
information ac
quisition comm
and is sent.
E2D
Receiv
e-data checksum err
or w
hen sending EEPROM infor
mation
acquisition command
T
he checksum of receive data is invalid
w
h
en a slave-EEPROM information
acquisition command is sent.
E33
Slave res
ponse logic error
T
he slave response l
ogic is i
n
valid.
E34
Slave block number out of range
T
he slave bloc
k number is out of range.