Maxim Integrated DS4830 Optical Microcontroller - Manual (Page 65)

DS4830 User’s Guide
65
8.2 – Sample and Hold Register Descriptions
The sample and hold has two SFRs. These are Sample and Hold Control Register (SHCN) and Sample and Hold Internal
Trigger Enable register (SENR). The SHCN register controls both sample and holds. The SENR controls the internal
sample pulse for both sample and holds. The sample and hold SFRs are located in module 2.
8.2.1
– Sample and Hold Control Register (SHCN)
SHCN Register Address: M2[10h]
Bit
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name SSC[3:0] FAST_MODE PIN_DIS1 PIN_DIS0 SH_DUAL - SH1_ALIGN SHDAI1_EN SMP_HLD1 CLK_SEL SH0_ALIGN SHDAI0_EN SMP_HLD0
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Access rw rw rw rw rw rw rw rw r rw rw rw rw rw rw rw
BIT NAME DESCRIPTION
15:12 SSC[3:0]
STOP Sample Control. These bits control the end of the sample and hold sampling
relative to the SHEN0 and SHEN1 pulse.
CLK_SEL = 0
SSC[3:0] STOP Sampling
0000 Falling Edge of SHEN0/SHEN1
0001 Reserved
0010 Reserved
0011 Reserved
0100 300ns after rising edge of SHEN0/SHEN1
0101 350ns after rising edge of SHEN0/SHEN1
0110 450ns after rising edge of SHEN0/SHEN1
0111 550ns after rising edge of SHEN0/SHEN1
1000 750ns after rising edge of SHEN0/SHEN1
1001 1us after rising edge of SHEN0/SHEN1
1010 1.5us after rising edge of SHEN0/SHEN1
1011 1.75us after rising edge of SHEN0/SHEN1
1100 2us after rising edge of SHEN0/SHEN1
1101 2.5us after rising edge of SHEN0/SHEN1
1110 4us after rising edge of SHEN0/SHEN1
1111 5us after rising edge of SHEN0/SHEN1
CLK_SEL = 1
SSC[3:0] STOP Sampling
0000 Falling Edge of SHEN0/SHEN1
0001 21 ext-clock after rising edge of SHEN0/SHEN1
0010 22 ext-clock after rising edge of SHEN0/SHEN1
0011 23 ext-clock after rising edge of SHEN0/SHEN1
0100 24 ext-clock after rising edge of SHEN0/SHEN1
0101 25 ext-clock after rising edge of SHEN0/SHEN1
0110 26 ext-clock after rising edge of SHEN0/SHEN1
0111 27 ext-clock after rising edge of SHEN0/SHEN1
1000 28 ext-clock after rising edge of SHEN0/SHEN1
1001 29 ext-clock after rising edge of SHEN0/SHEN1
1010 30 ext-clock after rising edge of SHEN0/SHEN1
1011 31 ext-clock after rising edge of SHEN0/SHEN1
1100 32 ext-clock after rising edge of SHEN0/SHEN1
1101 33 ext-clock after rising edge of SHEN0/SHEN1
1110 34 ext-clock after rising edge of SHEN0/SHEN1
1111 35 ext-clock after rising edge of SHEN0/SHEN1
Note: A minimum sample time of 300nSec must be used when external clock is used
to guarantee accurate results.
11 FAST_MODE Fast Mode Enable. Setting this bit to ‘1’ enables the fast operation for Sample and Hold 0.
In this mode, the Sample and Hold 0 is guaranteed to get a conversion slot in the ADC
conversion sequence every 125

s and the user can issue sample pulses at an interval of