Cabletron Systems 1800 - Manual (Page 440)

Idx-2 SmartSwitch 1800 4. 0 User G uide, Rev 01
Character
Change Field 2-7
Select Option 2-7
Character Delete 12-5
Clear Max Stats 2-6
Clear VC on Last Device Down 10-6
Clearing causes B-1
async A-5
Collecting Node 4-5
Collecting Node ID 4-4
Collecting Node Pwd (password) 4-4
Command mode (async terminal) A-1
Committed Burst Size (In/Out) 7-18
Committed Information Rate (In/Out) 7-18
Community Table, configuring 17-2
Configuration database 3-1
Configuration report 3-9
Configure Model Number 3-10 , F-1
Connection ID 10-7
Connection Priority 7-21 , 8-26 , 8-34 , 9-16 , 10-10 , 11-
10 , 12-17 , 12-19
Connections, displaying 20-3
Controller Type 11-6
Copying a database record 2-6
Country Code 13-4
CSU/DSU Operating Mode 7-17 , 8-9
CSU/DSU tests 19-15
D
Data Forwarding Char 12-4
Data Forwarding Criteria 12-14
Data transfer mode (async terminal) A-1
Database 3-1
backing up 19-6
files 19-9
restoring 19-6
setup recommendations 3-1
Database and system memory values 4-2 , 6-3
Date, changing 2-8
DCE Cable Attached 12-11
Default Calling Address 8-11 , 8-19 , 12-11
Default Ethernet Frame Type 16-5
Default Packet Size 8-11 , 8-18
Default Window Size 8-11 , 8-18
Del 14-6
Delay Retry Count 11-6
Delay Timer 11-6
Delete (BSC subscriber) 10-3 , 11-7
Delete CUG 8-20
Delete? 7-23
Deleting a database record 2-6
Destination IP Address 14-11 , 14-12
Destination MAC Address Value 16-9
Destination Mask 14-15
Destination NetBIOS Name 16-10
Destination Network Value 15-7
Destination Node Value 15-7
Destination Socket Value 15-7
Destination Subscriber 14-12 , 15-15
Devices Connected 12-14
Diagnostic codes B-2
SmartSwitch-specific B-4
SNA B-4
X.25 B-2
Dial port, configuring 8-5
Dial Support 8-12
Dial Timer 13-14
Disable Request Disconnect 9-10
Disable Status Response 10-12
Disable X.121 User Calls 12-11
Discard Output 12-5
Disconnect Duration 12-13
Disconnect if Clear Recvd 12-13
Disconnect if Clear Sent 12-14
Disconnect Timer 8-13 , 12-13
Display All CUGs 8-20
DLCI configuration, reviewing 7-10
DLCI parameters, configuring 7-12
DLCI sharing 7-1
DLCIs, learned 7-13
Dotted decimal notation 14-1
DSAP Value 16-9
DSU/CSU tests 19-15
DTE Clear Retry Count 8-12 , 8-19
DTE Reset Retry Count 8-12 , 8-19
DTE Restart Retry Count 8-12 , 8-19
DTMF Detection 13-10
DTMF Off Duration 13-16
DTMF On Duration 13-16
DTR/RTS Active When VC Up 12-12
Dynamic Signaling Action 12-14
E
EBCDIC 10-4 , 11-5
Echo 12-4
Echo Mask 12-6
Edit Service Signal 12-6
Editing (in async PAD profile) 12-5
Enable Backup Protocol? 7-19
Enable Bandwidth Allocation 7-18
Enable Inverse ARP 14-11
Enable Outgoing Rate Control 7-18
Enabled (traps) 17-5
Encapsulation Method 8-16
End-to-End Acknowledgement 10-4
Entry 7-22