Enabling and setting up staggered spin-up – Avago Technologies 3ware SAS 9750-16i4e User Manual
Page 86

Chapter 6. Configuring Your Controller
74
3ware SATA+SAS RAID Controller Card Software User Guide, Version 10.2
Setting the Size of Volumes Created with
Auto-Carving
You can use auto-carving to divide units larger than 1 TB into multiple
volumes. You control the size of the volumes to be created by setting the carve
size (referred to as carving factor in 3BM). The carve size can be between
1 TB (1024 GB) and 32 TB (32768 GB); the default is 2 TB.
When you change this policy, it applies to units you create in the future.
Existing units will not be affected.
To set the carve size in 3DM2
1
Choose
Management >> Controller Settings
from the menu bar in
3DM2.
2
In the Other Controller Settings section at the bottom of the screen, in the
Carve Size
field, enter the size you want (between 1024 GB and
32768 GB) to use and click
Submit
.
The page refreshes, and a message at the top confirms the change you
have made.
To set the carve size (carving factor) in 3BM
1
On the main 3BM screen,
Tab
to
Settings
and press
Enter
.
2
On the pop-up menu, select
Controller Policies
and press
Enter
.
3
On the Policy Settings page,
Tab
to the
Carving Factor
field, press
Enter
to display the text entry box, enter the size you want (between 1024 GB
and 32768 GB) and press
Enter
again to accept it.
4
Tab
to
OK
and press
Enter
to select it.
The policy is enabled immediately.
Enabling and Setting Up Staggered Spin-up
You can set the number of SAS and SATA drives that will spin up at the same
time and the delay time between drive group spinups. This does not apply to
SAS or SATA drives that are attached to an expander.
Three policy settings let you set the number of drives that will spin up at the
same time and set the delay between drive groups that spin up at one time.
Not all SATA drives support staggered spinup. If you enable staggered spinup
and have drives that do not support it, the setting will be ignored. You can
change these settings in 3BM or using the CLI.
- 3ware SAS 9750-24i4e 3ware SAS 9750-4i 3ware SAS 9750-4i4e 3ware SAS 9750-8e 3ware SAS 9750-8i 3ware 8006-2LP 3ware 8006-2LP (Channel) 3ware 9550SXU-4LP 3ware 9550SXU-4LP (Channel) 3ware 9550SXU-8LP 3ware 9550SXU-8LP (Channel) 3ware 9650SE-12ML 3ware 9650SE-12ML (Channel) 3ware 9650SE-16ML 3ware 9650SE-16ML (Channel) 3ware 9650SE-24M8 3ware 9650SE-24M8 (Channel) 3ware 9650SE-2LP 3ware 9650SE-2LP (Channel) 3ware 9650SE-4LPML 3ware 9650SE-4LPML (Channel) 3ware 9650SE-8LPML 3ware 9650SE-8LPML (Channel) 3ware 9690SA-4I 3ware 9690SA-4I (Channel) 3ware 9690SA-4I4E 3ware 9690SA-4I4E (Channel) 3ware 9690SA-8E 3ware 9690SA-8E (Channel) 3ware 9690SA-8I 3ware 9690SA-8I (Channel)