Index – HEIDENHAIN CNC Pilot 4290 V7.1 User Manual
Page 705
HEIDENHAIN CNC PILOT 4290
705
Index
G402 Circular pattern on front/rear
G411 Linear pattern on lateral
G412 Circular pattern on lateral
G49 Hole (centric) ... 162
G52 Blockwise oversize ... 166
G7 Precision stop on ... 164
G8 Precision stop off ... 164
G9 Precision stop blockwise ... 164
G95 Feed per revolution ... 166
G functions for machining
G0 Rapid traverse ... 187
G1 Linear path ... 189
G100 Rapid traverse on front/rear
G101 Linear segment on front/rear
G102 Circular arc on front/rear
G103 Circular arc on front/rear
G119 No. of C axis ... 253
G12 Circular path ... 191
G120 Reference diameter ... 253
G121 Mirror/shift contour ... 202
G13 Circular path ... 191
G14 Tool change position ... 187
G147 Safety clearance (milling
G149 Additive compensation ... 209
G15 Move rotary axis ... 303
G150 Compensation of right-hand
G151 Compensation of left-hand
G152 Zero point shift, C axis ... 254
G153 Standardize C axis ... 254
G162 Synchronization
G192 Feed per minute for rotary
G2 Circular path ... 190
G204 Wait for moment ... 305
G26 Speed limitation ... 192
G3 Circular path ... 190
G30 Converting and mirroring ... 282
G31 Thread cycle ... 240
G32 Simple thread cycle ... 242
G33 Thread single path ... 244
G36 Tapping ... 250
G4 Period of dwell ... 302
G40 Switch off TRC/MCRC ... 197
G41 Switch on TRC/MCRC ... 197
G42 Switch on TRC/MCRC ... 197
G47 Safety clearance ... 206
G48 Acceleration (slope) ... 192
G50 Switch off oversize ... 204
G51 Zero point shift ... 199
G53 Parameter-dependent zero
G56 Additive zero point shift ... 200
G57 Axis-parallel oversize ... 204
G58 Contour-parallel oversize ... 205
G59 Absolute zero point shift ... 201
G60 Switch off protection
G600 Preselect tool ... 723
G62 One-sided
G64 Interrupted feed rate ... 193
G65 Chuck selection ... 304
G66 Component position ... 305
G7 Precision stop on ... 302
G701 Rapid traverse to machine
G702 Saving/loading contour follow-
G703 Contour follow-up ... 294
G706 K default branch ... 295
G71 Drilling cycle ... 246
G710 Adding tool dimensions ... 211
G717 Updating nominal
G718 Move lag error ... 306
G72 Boring, countersinking ... 248
G73 Tapping ... 249
G74 Deep-hole drilling cycle ... 251
G799 Thread milling, axial ... 278
G8 Precision stop off ... 302
G80 End of cycle ... 231
G801 Engraving on front face ... 279
G802 Engraving on lateral
G810 Longitudinal roughing ... 212
G82 Simple face roughing ... 232
G820 Face roughing ... 215
G830 Contour-parallel
G835 Contour-parallel with neutral
G840 Contour milling ... 261
G845 Pocket milling,
G85 Undercut cycle ... 235
G86 Simple recessing cycle ... 236
G860 Contour-based
G866 Recessing cycle ... 224
G869 Recess turning cycle ... 225
G87 Line with radius ... 238
G88 Line with chamfer ... 238
G890 Contour finishing ... 228
G9 Precision stop ... 302
G901 Actual values in
G903 Lag error in variables ... 306
G905 C-angle offset ... 287
G906 Measuring angular offset
during spindle
synchronization ... 288
G909 Interpreter stop ... 307
G910 Switch on in-process