Synchronisation interfaces for iqs-8140, Ethernet add/drop interfaces for iqs-8105/15/20/30, Specifications – EXFO IQS-8100 Series Transport Blazer for IQS-600 User Manual
Page 587: Sonet/sdh application
Specifications
SONET/SDH Application
573
Synchronisation Interfaces for IQS-8140
Synchronisation Interfaces for IQS-8140
Ethernet Add/Drop Interfaces for
IQS-8105/15/20/30
External Clock DS1/1.5M
External Clock E1/2M
External Clock E1/2M
2 MHz (Trigger)
Tx pulse amplitude
2.4 to 3.6 V
3.0 V
2.37 V
0.75 to 1.5 V
Tx pulse mask
GR-499 figure 9.5
G.703 figure 15
G.703 figure 15
G.703 figure 20
Typical power dBdsx
+0.6 dBdsx (0-133 ft)
Tx LBO
+1.2 dBdsx (133-266 ft)
preamplification
+1.8 dBdsx (266-399 ft)
+2.4 dBdsx (399-533 ft)
+3.0 dBdsx (533-655 ft)
Rx level
TERM:
)6 dB (cable loss only)
TERM:
)6 dB (cable loss only)
TERM:
)6 dB (cable loss only)
)6 dB (cable loss only)
sensivity
(at 772 kHz for T1)
MON:
)26 dB (20 dB resistive loss
MON:
)26 dB (resistive loss
DSX-MON:
)26dB (20 dB
+ cable loss
) 6 dB)
+ cable loss
) 6 dB)
resistive loss + cable loss
) 6 dB)
Bridge:
)6 dB (cable loss only)
Bridge:
)6 dB (cable loss only)
Bridge:
)6dB (cable loss only)
Transmission bit rate
1.544 Mbit/s ± 4.6 ppm
2.048 Mbit/s ± 4.6 ppm
2.048 Mbit/s ± 4.6 ppm
Reception bit rate
1.544 Mbit/s ± 50 ppm
2.048 Mbit/s ± 50 ppm
2.048 Mbit/s ± 50 ppm
Intrinsic jitter (Tx)
ANSI T1.403 section 6.3
G.823 section 6.1
G.823 section 6.1
G.703 table 11
GR-499 section 7.3
Input jitter
AT&T PUB 62411
G.823 section 7.2
G.823 section 7.2
tolerance
GR-499 SECTION 7.3
G.813
G.813
Line coding
AMI and B8ZS
AMI and HDB3
AMI and HDB3
Input impedance
75
1 ± 5 %, unbalanced
75
1 ± 5 %, unbalanced
75
1 ± 5 %, unbalanced
75
1 ± 5 %, unbalanced
(resistive termination)
Connector type
BNC
a
BNC
a
BNC
BNC
SONET/SDH
OTN
Parameter
Value
Value
Tx pulse amplitude
600 ± 200 mVpp
600 ± 200 mVpp
Transmission frequency
2.48832 GHz
2.68865 GHz
Output configuration
AC coupled
AC coupled
Load impedance
50
1
50
1
Maximum cable length
1 m
1 m
Connector type
SMA
SMA
SYNCHRONIZATION INTERFACES
REF-OUT INTERFACE
NOTE
a. Adaptation cable required for BANTAM.
gger 2 MHz
5 to 1.5 V
703 figure 20
dB (cable loss only)
10/100/1000 Base-T (Add/Drop)
Compliance
10 Mbit/s: IEEE 802.3 section 14
100 Mbit/s: IEEE 802.3 section 25
1000 Mbit/s: IEEE 802.3 section 40
Connector
RJ-45 Ethernet
Gigabit Ethernet (Add/Drop)
Interface/connector
SFP/Dual LC
Compliance
1000 Mbit/s: IEEE 802.3 Section 40
b
Wavelength/Max Tx level
850, 1310 nm/—3 dBm
1550 nm/+5 dBm
ETHERNET ADD/DROP INTERFACE