EXFO IQS-8100 Series Transport Blazer for IQS-600 - Manual (Page 586)

Specifications
572 IQS-8100 Series Transport Blazer
Synchronization Interfaces for IQS-8105/15/20/30
Synchronization Interfaces for
IQS-8105/15/20/30
External Clock DS1/1.5M External Clock E1/2M External Clock E1/2M Trigger 2 MHz
Tx Pulse Amplitude 2.4 to 3.6 V 3.0 V 2.37 V 0.75 to 1.5 V
Tx Pulse Mask GR-499 figure 9.5 G.703 figure 15 G.703 figure 15 G.703 figure 20
Typical power dBdsx
+0.6 dBdsx (0-133 ft)
Tx LBO +1.2 dBdsx (133-266 ft)
Preamplification +1.8 dBdsx (266-399 ft)
+2.4 dBdsx (399-533 ft)
+3.0 dBdsx (533-655 ft)
Rx Level TERM: ≤ 6 dB (cable loss only) TERM: = ≤ 6 dB (cable loss only) TERM: = ≤ 6 dB (cable loss only) ≤ 6 dB (cable loss only)
Sensivity (at 772 kHz for T1) DSX-MON: MON: ≤ 26 dB (20 dB resistive loss MON: ≤ 26 dB (resistive loss
≤ 26 dB (20 dB resistive loss + cable loss ≤ 6 dB) + cable loss ≤ 6 dB)
+ cable loss ≤ 6 dB)
Bridge: ≤ 6 dB (cable loss only) Bridge: ≤ 6 dB (cable loss only) Bridge: ≤ 6 dB (cable loss only)
Transmission Bit Rate 1.544 Mbit/s ± 4.6 ppm 2.048 Mbit/s ± 4.6 ppm 2.048 Mbit/s ± 4.6 ppm
Reception Bit Rate 1.544 Mbit/s ± 50 ppm 2.048 Mbit/s ± 50 ppm 2.048 Mbit/s ± 50 ppm
Intrinsic Jitter (Tx) ANSI T1.403 section 6.3 G.823 G.823 G.703
GR-499 section 7.3 section 6.1 section 6.1 table 11
Input Jitter AT&T PUB 62411 G.823 section 7.2 G.823 section 7.2
Tolerance GR-499 SECTION 7.3 G.813 G.813
Line Coding AMI and B8ZS AMI and HDB3 AMI and HDB3
Input Impedance 75 ohms ± 5%, 75 ohms ± 5%, 75 ohms ± 5%, 75 ohms ± 5%,
(Resistive Termination) unbalanced unbalanced unbalanced unbalanced
Connector Type BNC a BNC a BNC BNC
10/100/1000 Base-T (Add/Drop)
Compliance
10 Mbit/s: IEEE 802.3 section 14
100 Mbit/s: IEEE 802.3 section 25
1000 Mbit/s: IEEE 802.3 section 40
Connector RJ-45 Ethernet
Gigabit Ethernet (Add/Drop)
Interface/connector
SFP/Dual LC
Compliance 1000 Mbit/s: IEEE 802.3 Section 40 b
Wavelength/Max Tx level 850, 1310 nm/—3 dBm
1550 nm/+5 dBm
NOTES
a. Adaptation cable required for BANTAM.
b. SFP/XFP transceivers comply with IEC 60825 and 21 CFR 1040.10
(except for deviations pursuant to Laser Notice 50, dated July, 2001), for Class 1 or 1M lasers.
SYNCHRONISATION INTERFACES ETHERNET ADD/DROP INTERFACE
REF-OUT INTERFACE
Parameter Value
Tx pulse amplitude 600 ± 150 mVpp
Transmission frequency
SONET/SDH/ 10 GigE LAN OTU2 OTU1e OTU2e
10 GigE WAN
Clock divider = 16 622.08 MHz 644.53 MHz 669.33 MHz 690.57 MHz 693.48 MHz
Clock divider = 32 311.04 MHz 322.266 MHz 334.66 MHz 345.29 MHz 346.74 MHz
Clock divider = 64 155.52 MHz 161.133 MHz 167.33 MHz 172.64 MHz 173.37 MHz
Output configuration AC coupled
Load impedance 50 ohms
Maximum cable length 3 meters
Connector Type
SMA