Operator interfaces 3-109 – WattMaster WCC II User Manual

Page 141

Section 3: Screen Descriptions

WCC II Operator’s Guide

Operator Interfaces

3-109

Step #2

: Now you must resave, or capture, the drawing in a

form that the ECC/WCC II system can interface with. To do this,
you must ﬁ rst load a ﬁ le named “Capture” which is sent from
WattMaster on a separate ﬂ oppy disk when the color graphics
option is purchased.

Step #3

: Then, with “Capture” present in the background, reload

the drawing package and get the image on the screen that you
would like to save.

Step #4:

Press and hold

and

, then press the

<[>

key, holding all three keys down at the same time, and then release
all of the keys at once. (The

is the shift key on the left

side of the keyboard.)

NOTE:

, and

must be disabled for the capture routine to work.

Step #5

: This “imageXX.img” ﬁ le is the picture that will be the

static background for the Enhanced Graphics Screen. This ﬁ le
needs to be copied (and renamed, if desired) to the same directory
or subdirectory as the ECC/WCC II software. The ECC/WCC II
software is sent from the factory on the root directory of the hard
disk. If your “imageXX.img” ﬁ le was created on the root directory
of the hard disk in the ECC/WCC II system, the ﬁ le is in the proper
place. If it was created on another computer and saved on a ﬂ oppy
disk, the ﬁ le can be copied to the hard disk using the following
commands:

Commands to transfer a ﬁ le to the ECC/WCC II hard
disk:

Step #1

: Insert the disk that contains the “imageXX.img” ﬁ les in

Drive A of the ECC/WCC II computer and close the drive door.

Step #2:

From the ECC/WCC II Main Menu, access the System

Parameters Screen and sign on with a level 3 password. Then
return to the Main Menu.

Step #3:

From the Main Menu, go to the Utility Screen and then

go to the WCC/SCC File Management Screen.

Step #4:

Fill out the screen to copy a ﬁ le from disk A to disk C.

In the following example, we are copying a ﬁ le named “image01.
img” from the disk in drive A to a ﬁ le called “ahu1.img” on the
disk in drive C. The “ahu1” can be anything up to 8 characters that
helps you identify each particular drawing.

---------------------------------------------

File name:

a:image01.img

New fi le name:

c:ahul.img

Direction:

WCC

Action:

Copy

---------------------------------------------

File name: a:image01.img

Type the name of the ﬁ le that is to be copied and press

The “a:” speciﬁ es the drive which has the disk with the ﬁ le to be
copied. If this is omitted, the system assumes the default drive.

New ﬁ le name: c:ahu1.img

Type the new ﬁ le name and press

. The “c:” speciﬁ es

the drive which has the disk which will receive the ﬁ le. If this is
omitted, the system assumes the default drive.

Direction: WCC

The direction category allows you to specify where the ﬁ le
management operation is to be performed. The following choices
are available:

SCC ->WCC

This option can be performed at the remote (SCC II)
computer only. The ﬁ le to be copied is at the remote
computer (SCC II), and the new ﬁ le will be written on
the disk at the on site computer (WCC II).

WCC

This choice can be selected for two different
situations. If you are at the remote computer, you may
select WCC and copy an existing ﬁ le at the on-site
computer to a new ﬁ le at the on-site computer. Or
this choice is selected if you want to perform a copy
command while you are physically at the on-site
computer.

Step #5:

After the ﬁ le has been transferred, press

several times until the cursor is back at the Utility Screen.