KEYENCE LT-9001 Series - Manual (Page 42)

2-24
Default Values and Settings Range
The default values and the settings range of the profile mode are shown below.
Profile Mode
E LT-9001-IM
Basic
Operations
2
Chapter
Chapter 5 "OPTIONAL Settings" - "DISPLAY UNIT"
(page 5-19)
Display unit μm μm,mil
Normal, High sensitivity
Profile mode
Program Run
Programs
GRAPH DISPLAY
Area ranges
OUT settings
(OUT1/OUT2)
Tolerance
Output
Calibration
Basic
settings
Optional
settings
Scan
Dark
Display
I/O
GAIN
Area
Smooth
Profile
output
Setting contents Reference pages Setting range
Default
value
30
+300.00
–300.00
+200.00
–200.00
–400
–300
+300
+400
+200.00
–200.00
2
0.00
Normal
[NORMAL]
A1(OUT1)
A2(OUT2)
+100.00
+100.00
0.00
1100/5
0.00
AVE
AVE
OFF
OFF
OFF
OFF
OFF
ON
ON
0
2
2
Binary
[BINARY]
Standard
Center fix
Chapter 5 "OUT Settings" - "CALIB" (page 5-16)
Chapter 4 “Measurement Screen” – “Display of
Profile Waveform” (page 4-6)
Chapter 4 “Light Intensity Screen” – “Changing
the Ranges of the Areas” (page 4-9)
Chapter 5 "OUT Settings" - "LIMITS" (page 5-7)
Chapter 4 "OUT Settings" - "Measurement"
(page 4-12)
Chapter 4 "BASIC Settings" - "AREA" (page 4-13)
Chapter 5 "OUT Settings" - "AVERAGE " (page 5-8)
Chapter 5 "OUT Settings" - "HOLD MODE"
(page 5-9)
Chapter 5 "OUT Settings" - "OFFSET" (page 5-14)
Chapter 5 "OUT Settings" - "ANALOG output"
(page 5-15)
Chapter 4 "BASIC Settings" - "SCAN WIDTH"
(page 4-14)
Chapter 4 "BASIC Settings" - "SCAN center" (page 4-15)
Chapter 4 "BASIC Settings" - "FINE mode" (page 4-15)
Chapter 4 "BASIC Settings" - "DARK" (page 4-16)
Chapter 4 "BASIC Settings" - "SMOOTH" (page 4-17)
Chapter 4 "OPTIONAL Settings" - "AUTO SLANT COR" (page 4-18)
Chapter 4 "OPTIONAL Settings" - "PROF OUT" (page 4-19)
Chapter 5 "OPTIONAL Settings" - "CAMERA IMAGE" (page 5-18)
Chapter 5 "OPTIONAL Settings" - "FOCUS" (page 5-18)
Chapter 4 “Light Insity Screen” – “Setting the Light
Intensity Level” (page 4-8)
Chapter 5 "OPTIONAL Settings" - "GRAPH DISPLAY" (page 5-18)
Chapter 5 "OPTIONAL Settings" - "DIGITS" (page 5-18)
Chapter 5 "OPTIONAL Settings" - "I/O" (page 5-20)
Chapter 5 "OPTIONAL Settings" - "GAIN" (page 5-20)
Normal [NORMAL], Auto peak hold [A.PEAK H],
Auto bottom hold [A BOTM H], Auto P-P hold
[A P-P H], Average hold [AVER. H],Peak hold
[PEAK HLD], Bottom hold [BOTTOM H], P-P
hold [P-P HOLD], Sample hold [SAMPLE H]
120/2, 120/5, 120/10,
250/2, 250/5, 250/10,
500/2, 500/5, 500/10,
1100/2, 1100/5,
1100/10
0~255
–9999.99 ~ +9999.99*
–9999.99 ~ +9999.99*
–9999.99 ~ +9999.99*
–9999.99 ~ +9999.99*
–550 ~ +550
–9999.99 ~ +9999.99*
2 ~ 128
AVE, MAX, MIN, DIFF
AVE, MAX, MIN, DIFF, AREA
–550 to +550
ON, OFF
ON, OFF
OFF, ON
OFF, 25%, 50%, 75%, 100%
ON, OFF
ON, OFF
OFF, 1-Digit, 2-Digit
Binary, Judgment output
Center fix, Maximum displacement,
Minimum displacement,
Average displacement
A1, A2, A1–A2, A1+A2
2, 4, 16
Light intensity level
Upper limit
Lower limit
Upper limit
Lower limit
Area1, range1
Area1, range2
Area2, range1
Area1, range2
Select
measurement
Number of measurement
times for averaging
Analog +10V
Analog –10V
Measurement mode
Offset
1st point/measured value
1st point/calibrated value
2nd point/measured value
2nd point/calibrated value
SCAN center
SCAN WIDTH
Camera Image
Focus
Graph display
Minimum number of
non-displayed digits
GAIN
I/O
AUTO SLANT COR
FINE Mode
Darkout
Averaging
Smoothing
Profile output
Area1
Area2
CORRECT
* The values differ according to the setting of the digit and the area.