KEYENCE LT-9001 Series - Manual (Page 170)

Index
[PAUSE] button ................................................1-6
Pause screen ............................3-2, 3-9, 4-2, 4-10
Peak hold [PEAK] ............................5-9, 5-11, 7-9
Peak-to-peak hold [P-P] ............................5-9, 7-9
PLC...................................................................8-1
Point data update cycle .................................7-11
Power LED........................................................1-4
Power ON reset time ........................................9-6
PROF OUT (Profile output) .............................4-19
Power switch ....................................................1-5
Profile graph display ........................................4-3
Profile mode ....................2-2, 2-9, 2-24, 4-1, 5-18
Profile output cycle.........................................7-11
Profile output time .................................7-11, 7-15
Profile waveform....................................7-11, 7-12
Profile waveform data output ....................8-4, 8-6
Profile waveform graph display........................4-4
Profile waveform output range .......................7-11
Program .............................................2-8, 6-2, 6-6
Program change ..............................................5-6
Program change screen ...........................3-2, 4-2
Program function ..............................................2-8
Program mode .................................................2-5
Program mode screen ..............................3-2, 4-2
Program No. change.................................7-4, 7-6
Program setting selection method [P-SELECT] ...6-2
[PROG/RUN] switch ..................................1-6, 6-4
[PROGRAM No.] button ...................................1-6
Program copy [P-COPY] ...........................6-2, 6-6
R
Range of light intensity graph ..........................4-4
Range of profile graph .....................................4-4
Received light intensity graph ..................3-7, 4-8
Remote control console ............................1-6, 6-6
Remote control console connector ..................1-4
RESET .......................................................8-4, 8-6
Reset input ................................................7-3, 7-5
RESET time ....................................7-9, 7-13, 7-14
Resetting the devices to the factory settings.....2-22
Response command ........................................8-3
Response delay time........................................9-6
RS-232C ...........................................................8-1
RS-232C cable.................................................A-5
RS-232C connector ..........................................1-4
RS-232C conversion adapter ..........................A-5
Run Mode .........................................................2-4
S
Sample hold [SAMPLE]....................5-9, 5-13, 7-9
Sampling cycle ..............................7-9, 7-13, 7-14
SCAN ....................................................3-15, 4-14
Scan center ...........................................3-16, 4-15
Scanning change time ............................7-9, 7-15
Scanning settings display bar..........................3-3
Scanning width cursor .....................................4-3
Scan width/interval ................................3-15, 4-14
Screen change ................................................. 8-4
[SCREEN] button..............................................1-6
SCROLL .........................................................5-18
Scrolling mode .....................................................5-18
Selecting an Item ...........................................2-11
Selecting the displacement mode .................2-13
Selecting the measurement target surface ....3-13
Selecting the profile mode .............................2-16
Selection method of the run mode .................2-12
SELECT SURFACE (Select surface)
................................................3-8, 3-12, 8-8, 8-10
Select surface position display bar ............3-3, 4-3
Select surface display ......................................3-4
Setting of number of data to be averaged .....8-10
Setting the area ..............................................2-18
Setting the light Intensity level ................2-15, 4-8
Setting the position ...................................3-7, 4-7
Setting the scan width/interval ..............2-14, 2-17
Setting the upper and lower limits of
the graph display ......................................3-6, 4-6
Setting the upper and lower limits display .....2-18
Single display............................................3-5, 4-5
Slant ...............................................................3-10
Slant correction .....................................3-10, 4-11
SMOOTH (average in profile mode only) .......4-17
Smoothing .............................................4-17, 8-13
SPAN .........................................................6-3, 6-7
Span adjustment ..............................................6-2
Specifications of the cable between the
Measuring unit and the controller ....................9-5
Specifications of the controller .........................9-2
Specifications of the measuring unit ................9-3
SRAM sum error...............................................A-4
STABILITY ........................................................7-5
Stability output ..........................................7-4, 7-5
A-14
E LT-9001-IM
Note: Pages marked in BOLD print refer to RS232C parameters, settings, etc.
Appendices
LT-9000-M-APP-E.qxd 10.4.8 6:02 PM ページA-14