KEYENCE LT-9001 Series - Manual (Page 150)

Specifications
9
Chapter
E LT-9001-IM
Specifications of the Controller
Model Controller unit/ LT-9501/LT-9010M LT-9501SO (5652)/LT-9030M
sensor head LT-9001/LT-9010 LT-9001SO (5653)/LT-9030
LT-9501H/LT-9011M LT-9501HSO (5654)/LT-9031M
LT-9001H/LT-9011 LT-9001HSO (5655)/LT-9031
Measuring unit compatibility Measuring units are interchangeable without factory recalibration.
Minimum display unit * 1 0.01 µm, 1 µm 2 , 0.01° 0.01 µm
Display range * 2 ±9999.99 µm, ±999999 µm 2 , ±9999.99° ±9999.99 µm
Microscope function Available (LT-9501 only) Available (LT-9501SO (5652) only)
Display cycle * 3 10 times/sec.
Analog output ±10 V x 2 output, output impedance 100 Ω
Timing input
Reset input
Non-voltage input
Auto-zero input
Monitor dedicated power supply * 4 24VDC, 1A
Judgment mode * 5 3-step Judgment output For OUT1 and OUT2 NPN open collector output
Binary output
Measurement data output (21 bit)
OUT1/OUT2/PROFILE selectable, NPN open collector output
Binary mode * 5 Strobe output NPN open collector output
Binary selection output NPN open collector output
Binary selection input Non-voltage input
Stability output NPN open collector output
Laser remote input Non-voltage input
Program change input Non-voltage input x 3 inputs
RS-232C interface
Measurement data output and control I/O
(Selectable up to baud rate 115200 bits/s)
Video output NTSC compliant (PIN connector)
Distance measurement,
Distance measurement,
Transparent object thickness measurement,
Transparent object thickness measurement,
Angle measurement,
Surface selection,
Displacement mode * 6 Relative angle measurement,
Dark-out, Mask,
Surface selection, Dark-out,
Trend graph display,
Mask, Trend graph display,
and Scan width/interval change
and Scan width/interval change
Area selection, Area calculation
(Average, Maximum, Minimum,
Maximum - minimum, Area) ,
Main function
Profile mode * 6
Scan width/interval change, Dark-out,
Smoothing, Averaging, and
Profile data output
Light intensity accumulation,
Microscope (LT-9501 and LT-9501SO(5652) only),
Common Tolerance judgement, 8-program registration,
Calibration, Averaging, Hold modes, Auto-zero,
and interface language selection
Power voltage AC 100-240 V ±10% 50/60 Hz
Rating
Current consumption 110 VA or lower
Overvoltage category II
Pollution degree 2
Environmental resistance
Operating ambient temperature 0 to +35°C
Operating ambient humidity 35 to 85%RH (No condensation)
Weight Approx. 2.4 kg
Terminal
block
Display
Control
I/O
9-2
Specifications
*1 The minimum display unit is 0.1 µm for LT-9501H/LT-9001H/LT-9501HSO (5654)/LT-9001HSO (5655) (the display changes every 0.3 µm).
*2 When the controller is used in combination with LT-9011M/LT-9011/LT-9031M/LT9031, the last digit displayed shows "0".
*3 Varies depending on the setting.
*4 Dedicated power supply for the monitor specified by KEYENCE. (CA-MN80 or CV-M30)
*5 Select either the limits mode or the binary mode
*6 Select either the distance mode or the profile mode.
The rating of the NPN open collector is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V.
The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower.