KEYENCE DV-90 - Manual (Page 257)

Appendix-21
App
endix
E DV-90-IM
11
Index
Numerics
2-Point Verification .....................................4-34, 8-8
3-Point-A Verification ....................... 4-21, 8-7, 9-20
3-Point-B Verification ....................... 4-28, 8-8, 9-22
A
Accessible Devices ............................................... 9-3
ACK/ANK protocol ............................................. 8-5
Active Verification ....................................4-13, 9-17
Additional information ..................................6-6, 8-9
Additional Verify Information ............................. 6-7
ASCII Code Table ............................................... A-5
AutoID Navigator ................................................. 2-7
B
Backlight ............................................................ 6-12
Basic Settings ....................................................... 7-7
Baud rate .............................................................. 6-9
BCD output .......................................................... 6-8
Binary output ........................................................6-7
Bit output .............................................................. 6-7
BL SetUp Software .............................................. 2-7
Buzzer ................................................................. 6-13
C
CE Marking ............................................................. 2
Checking the Package Contents ........................... 1-2
Checking the Type of the Read Barcode ............ 2-10
Code reader 1 type ................................................ 6-5
Code reader 2 type ................................................ 6-5
Code Reader Setup Basics .................................... 2-2
Command communication ................................... 8-2
Command Communication Details .................... 8-10
Communication Form .......................................... 8-2
Communication Format ...................................... 8-10
Communication menu .......................................... 7-6
Communication Procedure for
the Setting Commands .................................... 8-12
Communication Protocol ...................................... 8-4
Communication settings ....................................... 6-9
Connectable combinations ................................. 1-12
Connecting a PC ................................................. 3-10
Connecting a PC or PLC .................................... 3-10
Connecting code readers of other
manufacturers .................................................. 3-10
Connecting the BL-1300 Series or
the SR-600/500 Series ...................................... 3-9
Connecting the BL-700/600/180 Series,
HR-50RK/40RK, or BL-210RK/N70RKE ....... 3-8
Connecting the BL-U1 ......................................... 3-9
Connecting the cable ............................................ 3-3
Connecting the Code Reader ................................ 3-8
Connecting the KV programming port ............... 3-11
Connecting the KV-L20V or KV-L20R ............ 3-11
Connecting the MELSEC Series ....................... 3-12
Connecting the N-400 or N-410 .......................... 3-9
Connecting the N-R2 or BL-U2 .......................... 3-9
Connecting the SYSMAC Series ....................... 3-12
Connecting the TL-800 ........................................ 3-8
Connection with the HR-UC51, BL-N9R,
and TL-70R ...................................................... 3-8
Counter Function ................................................. 4-9
Crimp-type terminal ........................................... 3-24
D
Data communication ............................................ 8-2
Data Communication Details ............................... 8-4
Data Editing in the Preset Mode ........................ 5-18
Data format .......................................................... 6-9
Data Write Timing ............................................. 9-17
Date .................................................................... 6-13
Date Compare ........................................... 5-10, 7-19
Description of Direct Control Commands ......... 8-11
Details on DM Assignment ................................. 9-6
Device Assignment .............................................. 9-4
Difference in Send Data Contents Due to
Verification Pattern .......................................... 8-6
Dimensions ..........................................................A-3
DM Assignment List ............................................ 9-4
DM head address ............................................... 6-10
DM that checks the current operation status ...... 9-13
DM that detects the occurrence of a reset .......... 9-12
DM that releases the interlock ........................... 9-12
DM that reports the start of operation to
the PLC ............................................................. 9-6
DMs in which data is written ............................. 9-15
DMs in which various data is written ................ 9-14
DMs that change the active record number in
“Verify Active” .............................................. 9-11
DMs that control the read trigger ......................... 9-8
DMs that report the head address of
the data write destination .................................. 9-7
DMs that report to the PLC that the
data writing is completed ............................... 9-10
DV-90PE (PNP open collector output type) ........ 1-2
E
Edit menu ............................................................. 7-6
Error Codes of Command Communication ....... 8-12
Error Display List .............................................. 7-39
Error display on the SetUp Software ................. 7-39
Error Messages ....................................................A-4
Exiting procedure ................................................. 7-5
F
Factory Setting List ..............................................A-9
File menu ............................................................. 7-6
Format Error ............................................. 4-23, 4-36