Lenze EVS93xx CrossCutter - Manual (Page 214)

Cross Cutter
Appendix
Prepared Solution Servo PLC / ECSxA 1.1 EN 6-46
Possible settings: Code
Default Selection
Comment
Display code: Reject length induces start/stop operation of cross
cutter.
TRUE
The selected reject length exceeds the limit
cutting length for start/stop operation =>
The pause will be extended accordingly in
the asynchronous motion phase.
C3701/
000
0 0 {1} 1
FALSE The selected reject length undershoots the
limit cutting length for start/stop operation.
Display code: Test length induces start/stop operation of cross
cutter.
TRUE
The selected test length exceeds the limit
cutting length for start/stop operation =>
The pause will be extended accordingly in
the asynchronous motion phase.
C3702/
000
0 0 {1} 1
FALSE The selected test length undershoots the
limit cutting length for start/stop operation.
Display code: Start/stop length induces start/stop operation of
cross cutter.
TRUE
The selected start/stop length exceeds the
limit cutting length for start/stop operation
=> The pause will be extended accordingly
in the asynchronous motion phase.
C3703/
000
0 0 {1} 1
FALSE The selected start/stop length undershoots
the limit cutting length for start/stop
operation.
C3704/
000
- - {0.0001
[m_units]}
- Display code: Starting point of pause in motion profile for cutting
length. Only if C3700/000 = TRUE.
C3705/
000
- - {0.0001
[m_units]}
- Display code: Starting point of pause in motion profile for reject
length. Only if C3701/000 = TRUE.
C3706/
000
- - {0.0001
[m_units]}
- Display code: Starting point of pause in motion profile for test
length. Only if C3702/000 = TRUE.
C3707/
000
- - {0.0001
[m_units]}
- Display code: Starting point of pause in motion profile for
start/stop length. Only if C3703/000 = TRUE.
C3708/
000
- - {0.0001
[m_units]}
- Display code: Finishing point of pause in motion profile for cutting
length. Only if C3700/000 = TRUE.
C3709/
000
- - {0.0001
[m_units]}
- Display code: Finishing point of pause in motion profile for reject
length. Only if C3701/000 = TRUE.
C3710/
000
- - {0.0001
[m_units]}
- Display code: Finishing point of pause in motion profile for test
length. Only if C3702/000 = TRUE.
C3711/
000
- - {0.0001
[m_units]}
- Display code: Finishing point of pause in motion profile for
start/stop length. Only if C3703/000 = TRUE.
C3712/
000
- - {0.0001
[m_units]}
- Display code: Material length which the cross cutter works to as a
cutting length in the motion profile in the asynchronous motion
phase. The value is the difference between the cutting length and
the synchronous X length.
Note: The value of this code is only recalculated during a
calculation sequence.
C3713/
000
- - {0.0001
[m_units]}
- Display code: Material length which the cross cutter works to as a
reject length in the motion profile in the asynchronous motion
phase. The value is the difference between the reject length and
the synchronous X length.
Note: The value of this code is only recalculated during a
calculation sequence.
C3714/
000
- - {0.0001
[m_units]}
- Display code: Material length which the cross cutter works to as a
test length in the motion profile in the asynchronous motion
phase. The value is the difference between the test length and
the synchronous X length.
Note: The value of this code is only recalculated during a
calculation sequence.