Avaya Cajun P550R - Manual (Page 678)

Command Reference Guide for the P550R, P580, P880, and P882 Multiservice Switches, v5.3.1 Index-xi
Index
show time zone , 25-4
snmp get get , 25-5
snmp next , 25-6
snmp set , 25-7
snmp walk , 25-11
snmp-server community , 25-8
snmp-server contact , 25-9
sntp server , 25-10
snmp get get , 25-5
snmp next , 25-6
snmp set , 25-7
snmp walk , 25-11
snmp-server community , 25-8
snmp-server contact , 25-9
snooping
CGMP , 14-12
snooping statistics
clearing CGMP , 14-3
sntp server , 25-10
STAP command
set spantree hello , 26-5
STAP commands , 26-1
set 3com-mapping-table , 26-2
set spantree , 26-2
set spantree config , 26-3
set spantree fwddelay , 26-4
set spantree maxage , 26-6
set spantree port , 26-7
set spantree portcost , 26-9
set spantree portpri , 26-10
set spantree port-top-change-detection , 26-7
set spantree priority , 26-11
show 3com-mapping-table , 26-12
show spantree , 26-12
show spantree config , 26-14
show spantree port , 26-15
static client ports
removing from intelligent multicast , 14-8
static session , 14-38
statistics
LGMP client , 14-10
udp , 10-46
viewing CGMP , 14-31
viewing LGMP , 14-40
Switch Fab commands
set fabric configure-redundant-hardware ,
27-2
set fabric enable-redundant-element , 27-3
set fabric toggle-active-controller , 27-4
show fabric status , 27-5
Switch IP commands
clear arp , 28-2
clear ip route , 28-3
set ip route , 28-4
show arp , 28-5
show interface , 28-6
show ip route , 18-2, 28-7, 28-8
System commands , 29-1
boot system flash , 29-3
copy (running-config) , 29-5
copy (startup-config) , 29-5
copy (tftp) , 29-7
copy running-config , 29-12
copy running-config startup-config , 29-13
copy running-config tftp , 29-14
copy startup-config , 29-15
copy startup-config running-config , 29-16
copy startup-config tftp , 29-17
copy tftp , 29-8, 29-9, 29-10, 29-11, 29-18, 29-22
copy tftp bootflash , 29-19, 29-24
copy tftp flash , 29-20, 29-25
copy tftp running-config , 29-27
copy tftp startup-config , 29-28
dir , 29-33
erase , 29-34
erase int-configs , 29-35
erase legacy-configs , 29-36
erase scripts , 29-37
erase startup-config , 29-38
ip http help server , 29-41
nvram initialize , 29-42
reload , 29-43
reset , 29-44
setup , 29-48
show boot , 29-49, 29-50, 29-51
show file_name , 29-52
show flash , 29-53
show running-config , 29-54
show startup-config , 29-55
show version , 29-56
T
tcp connections , 10-44, 10-45
telnet
UI commands , 31-14
using , 1-5
Temperatures commands
clear temperatures , 30-2
set temperature (shutdown) , 30-3
set temperature (warning) , 30-5
show temperature , 30-7
terminal databits
UI command , 31-16
terminal flowcontrol , 31-17
terminal length , 31-18