beautypg.com

Appn – IBM SC30-3865-04 User Manual

Page 97

background image

Edit Dependent LU Server: (Y)es (N)o [N]?

Allow CP-CP sessions on this link (Y)es (N)o [Y]?

CP-CP session level security (Y)es (N)o [N]?

Configure CP name of adjacent node: (Y)es (N)o [N]?

Edit TG Characteristics: (Y)es (N)o [N]?

Write this record? [Y]?

The record has been written.
APPN config>list link tosecstn

STATION:

Port name: SDLC001

Interface number(DLSw = 254): 1

Link Type: SDLC

Station address: C1

Activate link automatically: YES

Allow CP-CP sessions on this link: YES

CP-CP session level security: NO

Fully-qualified CP name of adjacent node:

Encryption key: 0000000000000000

Use enhanced session security only: NO

Cost per connect time: 0

Cost per byte: 0

Security:(0 = Nonsecure, 1 = Public Switched Network

2 = Underground Cable, 3 = Secure Conduit,

4 = Guarded Conduit, 5 = Encrypted, 6 = Guarded Radiation): 0

Propagation delay:(0 = Minimum, 1 = Lan, 2 = Telephone,

3 = Packet Switched Network, 4 = Satellite, 5 = Maximum): 2

Effective capacity: 45

First user-defined TG characteristic: 128

Second user-defined TG characteristic: 128

Third user-defined TG characteristic: 128

Predefined TG number: 0

APPN config>act

***********************************************************************

* Configuring a Secondary Point-To-Point SDLC Station:

2

***********************************************************************

Config> set data sdlc 1

Config> n 1

SDLC user configuration

SDLC 1 Config> set link role secondary

SDLC 1 Config> set link cable rs-232 dte

SDLC 1 Config>list link

**(will show link configuration)

SDLC 1 Config>add station

Enter station address (in hex) [C1]?

Enter station name [SDLC_C1]?

Include station in group poll list ([Yes] or No): no

Enter max packet size [2048]?

Enter receive window [7]?

Enter transmit window [7]?

SDLC 1 Config>list station all

Address

Name

Status

Max BTU Rx Window Tx Window

------- -------- ---------- ------- --------- ---------

C1

SDLC_C1

ENABLED

2048

7

7

SDLC 1 Config>ex

Config> CTRL p

* restart

Are you sure you want to restart the gateway? (Yes or [No]): yes

* t 6

Config>p appn

APPN user configuration

APPN config>add port sdlc

APPN Port

Interface number(Default 0): [0]? 1

Port name (Max 8 characters) [SDLC001]?

Enable APPN on this port (Y)es (N)o [Y]?

Port Definition

Service any node: (Y)es (N)o [Y]?

Edit TG Characteristics: (Y)es (N)o [N]?

Write this record? [Y]?

The record has been written.

APPN config>list port sdlc001

**(will show port definitions)

APPN config>add link sdlc001

APPN Station

Station name (Max 8 characters) [ ]? TOPRISTN

Activate link automatically (Y)es (N)o [Y]?

(Note: "Y" to accept activation from the primary or negotiable station)

Station address(1-fe) [C1]?

Adjacent node type: 0 = APPN network node, 1 = APPN end node

2 = LEN end node, 3 = PU 2.0 node [0]?

APPN

Chapter 1. APPN

67