Watlow EZ-ZONE RMC - Manual (Page 82)

Watlow EZ-ZONE ® RMC Module • 79 • Chapter 4 Setup Page
RMC Module • Setup Page
Dis-
play
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter
ID
Data
Type
& Read/
Write
[`L;dd]
[ L.dd] Control Loop (1 to 4)
Open Loop Detect De-
viation
Set the value that the
process must deviate
from the set point to
trigger an open-loop
error.
-1,999.000 to 9,999.000°F or
units
-1,110.555 to 5,555.000°C
10.0°F or
units
6.0°C
2266
[offset 70] 0x97 (151)
1 to 4
0x18 (24)
76 8041 float
RWES
[``rP]
[ rP]
Control Loop (1 to 4)
Ramp Action
Select when the control-
ler's set point will ramp
to the defined end set
point.
[`oFF] Off (62)
[`Str] Startup (88)
[StPt] Set Point Change (85)
[both] Both (13)
Off 2526
[offset 80] 0x6B
(107)
1 to 4
0xE (14)
56 7014 uint
RWES
[`r;SC]
[ r.SC]
Control Loop (1 to 4)
Ramp Scale
Select the scale of the
ramp rate.
[hoUr] Hours (39)
[Min] Minutes (57)
Minutes 2528
[offset 80] 0x6B
(107)
1 to 4
0xF (15)
57 7015 uint
RWES
[`r;rt]
[ r.rt]
Control Loop (1 to 4)
Ramp Rate
Set the rate for the set
point ramp. Set the time
units for the rate with
the Ramp Scale param-
eter.
0.0 to 9,999.000°F or units
0.0 to 5,555.000°C 1.0°F or
units
1.0°C
2532
[offset 80] 0x6B
(107)
1 to 4
0x11 (17)
58 7017 float
RWES
[Pro;E]
[Pro.E] Control Loop (1 to 4)
Profiling Enable
Enable this loop to run
profiles.
[``no] No (59)
[`YES} Yes (106)
No 2552
[offset 80] 0x6B
(107)
1 to 4
0x1B (27)
- - - - 7027 uint
RWES
[`L;SP]
[ L.SP] Control Loop (1 to 4)
Low Set Point
Set the minimum value
of the closed loop set
point range.
-1,999.000 to 9,999.000°F or
units
-1,128.000 to 5,537.000°C
-1,999°F
or units
-1,128°C
2504
[offset 80] 0x6B
(107)
1 to 4
3
- - - - 7003 float
RWES
[`h;SP]
[ h.SP] Control Loop (1 to 4)
High Set Point
Set the maximum value
of the closed loop set
point range.
-1,999.000 to 9,999.000°F or
units
-1,128.000 to 5,537.000°C
9,999°F or
units
5,537°C
2506
[offset 80] 0x6B
(107)
1 to 4
4
- - - - 7004 float
RWES
[`C;SP]
[ C.SP] Control Loop (1 to 4)
Closed Loop Set Point
**
Set the set point that
the controller will auto-
matically control to.
-1,999.000 to 9,999.000°F or
units
-1,128.000 to 5,537.000°C
75.0°F or
units
24.0°C
2500
[offset
80]
0x6B
(107)
1 to 4
1
49 7001 float
RWES
[`id;S]
[ id.S] Control Loop (1 to 4)
Idle Set Point **
Set a closed loop set
point that can be trig-
gered by an event state.
-1,999.000 to 9,999.000°F or
units
-1,128.000 to 5,537.000°C
75.0°F or
units
24.0°C
2516
[offset
80]
0x6B
(107)
1 to 4
9
50 7009 float
RWES
Note:
Some values will be rounded off to fit in the four-character display .
Full values can be read with other interfaces .
Note:
If there is only one instance of a menu, no submenus will appear .
** These parameters/prompts are available in these menus with firmware revisions 6 .0 and
above .
R: Read
W: Write
E: EEPROM
S: User Set