Process value menu – Watlow EZ-ZONE RMC User Manual
Page 69
Watlow EZ-ZONE
®
RMC Module
•
66
•
Chapter 4 Setup Page
RMC Module • Setup Page
Dis-
play
Parameter Name
Description
Range
Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter
ID
Data
Type
& Read/
Write
[``Pu]
[`Set]
Process Value Menu
[``Fn]
[ Fn]
Process Value (1 to 4)
Function
Set the function that
will be applied to the
source or sources.
[`oFF]
Off (62)
[`S;bA]
Sensor Backup (1201)
[`Aug]
Average (1367)
[``C;o]
Crossover (1368)
[`W;b]
Wet Bulb Dry Bulb
(1369)
[``S;o]
Switch Over (1370)
[diFF]
Differential (1373)
[rAti]
Ratio (1374)
[`add]
Add (1375)
[MUL]
Multiply (1376)
[A;diF]
Absolute Difference
(1377)
[Min]
Minimum (1378)
[MAH]
Maximum (1379)
[root]
Square Root (1380)
[usla]
Vaisala (1648)
[`alt]
Pressure to Altitude
(1649)
Off
3440
[offset 70]
0x7E
(126)
1 to 4
0x15 (21)
123
26021
uint
RWES
[SFn;A]
[SFn.A]
Process Value (1 to 4)
Source Function A
Set the type of function
that will be used for this
source.
[``Ai]
Analog Input (142)
[``Pu]
Process Value (241)
Analog
Input
3400
[offset 70]
0x7E
(126)
1 to 4
1
- - - -
26001
uint
RWES
[Si;A]
[ Si.A]
Process Value (1 to 4)
Source Instance A
Set the instance of the
function selected above.
1 to 250
3410
[offset 70]
0x7E
(126)
1 to 4
6
- - - -
26006
uint
RWES
[SFn;b]
[SFn.b]
Process Value (1 to 4)
Source Function B
Set the type of function
that will be used for this
source.
[nonE]
None (61)
[``Ai]
Analog Input, (142)
[`Lnr]
Linearization (238)
[mat]
Math (240)
[``Pu]
Process Value (241)
[`uAr]
Variable (245)
None
3402
[offset 70]
0x7E
(126)
1 to 4
2
- - - -
26002
uint
RWES
[`si;b]
[ Si.b]
Process Value (1 to 4)
Source Instance B
Set the instance of the
function selected above.
1 to 250
1
3412
[offset 70]
0x7E
(126)
1 to 4
7
- - - -
26007
uint
RWES
[`s2;b]
[ SZ.b]
Process Value (1 to 4)
Source Zone B
Set the zone of the func-
tion selected above.
0 to 16
0
3422
[offset 70]
0x7E
(126)
1 to 4
0xC(12)
- - - -
26012
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display .
Full values can be read with other interfaces .
Note:
If there is only one instance of a menu, no submenus will appear .
** These parameters/prompts are available in these menus with firmware revisions 6 .0 and
above .
R: Read
W: Write
E:
EEPROM
S:
User Set